add all source code from linksys/broadcom which is free, to cvs for better maintainence inside

openwrt. this gives us the ability to better support different hardware models, without changing
any external tar-balls. only et.o and wl.o is missing and is fetched from my webserver.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk/openwrt@379 3c298f89-4303-0410-b956-a3cf2f4a3e73

1 files changed, 117 insertions, 0 deletions

diff --git a/package/linux/kernel-source/arch/mips/brcm-boards/bcm947xx/time.c b/package/linux/kernel-source/arch/mips/brcm-boards/bcm947xx/time.c
new file mode 100644
index 000000000..9b7574663
--- /dev/null
+++ b/package/linux/kernel-source/arch/mips/brcm-boards/bcm947xx/time.c
@@ -0,0 +1,117 @@
+/*
+ * Copyright 2004, Broadcom Corporation
+ * All Rights Reserved.
+ * 
+ * THIS SOFTWARE IS OFFERED "AS IS", AND BROADCOM GRANTS NO WARRANTIES OF ANY
+ * KIND, EXPRESS OR IMPLIED, BY STATUTE, COMMUNICATION OR OTHERWISE. BROADCOM
+ * SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A SPECIFIC PURPOSE OR NONINFRINGEMENT CONCERNING THIS SOFTWARE.
+ *
+ * $Id$
+ */
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/serial_reg.h>
+#include <linux/interrupt.h>
+#include <asm/addrspace.h>
+#include <asm/io.h>
+#include <asm/time.h>
+
+#include <typedefs.h>
+#include <bcmnvram.h>
+#include <sbconfig.h>
+#include <sbextif.h>
+#include <sbutils.h>
+#include <sbmips.h>
+
+/* Global SB handle */
+extern void *bcm947xx_sbh;
+extern spinlock_t bcm947xx_sbh_lock;
+
+/* Convenience */
+#define sbh bcm947xx_sbh
+#define sbh_lock bcm947xx_sbh_lock
+
+extern int panic_timeout;
+static int watchdog = 0;
+static u8 *mcr = NULL;
+
+void __init
+bcm947xx_time_init(void)
+{
+	unsigned int hz;
+	extifregs_t *eir;
+
+	/*
+	 * Use deterministic values for initial counter interrupt
+	 * so that calibrate delay avoids encountering a counter wrap.
+	 */
+	write_c0_count(0);
+	write_c0_compare(0xffff);
+
+	if (!(hz = sb_mips_clock(sbh)))
+		hz = 100000000;
+
+	printk("CPU: BCM%04x rev %d at %d MHz\n", sb_chip(sbh), sb_chiprev(sbh),
+	       (hz + 500000) / 1000000);
+
+	/* Set MIPS counter frequency for fixed_rate_gettimeoffset() */
+	mips_hpt_frequency = hz / 2;
+
+	/* Set watchdog interval in ms */
+	watchdog = simple_strtoul(nvram_safe_get("watchdog"), NULL, 0);
+	
+   	/* Please set the watchdog to 3 sec if it is less than 3 but not equal to 0 */
+	if (watchdog > 0) {
+		if (watchdog < 3000)
+			watchdog = 3000;
+	}
+
+
+	/* Set panic timeout in seconds */
+	panic_timeout = watchdog / 1000;
+
+	/* Setup blink */
+	if ((eir = sb_setcore(sbh, SB_EXTIF, 0))) {
+		sbconfig_t *sb = (sbconfig_t *)((unsigned int) eir + SBCONFIGOFF);
+		unsigned long base = EXTIF_CFGIF_BASE(sb_base(readl(&sb->sbadmatch1)));
+		mcr = (u8 *) ioremap_nocache(base + UART_MCR, 1);
+	}
+}
+
+static void
+bcm947xx_timer_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+{
+	/* Generic MIPS timer code */
+	timer_interrupt(irq, dev_id, regs);
+
+	/* Set the watchdog timer to reset after the specified number of ms */
+	if (watchdog > 0)
+		sb_watchdog(sbh, WATCHDOG_CLOCK / 1000 * watchdog);
+
+#ifdef	CONFIG_HWSIM
+	(*((int *)0xa0000f1c))++;
+#else
+	/* Blink one of the LEDs in the external UART */
+	if (mcr && !(jiffies % (HZ/2)))
+		writeb(readb(mcr) ^ UART_MCR_OUT2, mcr);
+#endif
+}
+
+static struct irqaction bcm947xx_timer_irqaction = {
+	bcm947xx_timer_interrupt,
+	SA_INTERRUPT,
+	0,
+	"timer",
+	NULL,
+	NULL
+};
+
+void __init
+bcm947xx_timer_setup(struct irqaction *irq)
+{
+	/* Enable the timer interrupt */
+	setup_irq(7, &bcm947xx_timer_irqaction);
+}