diff options
Diffstat (limited to 'target/linux')
4 files changed, 331 insertions, 2 deletions
diff --git a/target/linux/kirkwood/config-3.3 b/target/linux/kirkwood/config-3.3 index b1cace766..44b8a0c58 100644 --- a/target/linux/kirkwood/config-3.3 +++ b/target/linux/kirkwood/config-3.3 @@ -99,6 +99,8 @@ CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_MACH_D2NET_V2 is not set # CONFIG_MACH_DB88F6281_BP is not set CONFIG_MACH_DOCKSTAR=y +CONFIG_MACH_GOFLEXNET=y +CONFIG_MACH_GOFLEXHOME=y # CONFIG_MACH_ESATA_SHEEVAPLUG is not set # CONFIG_MACH_GURUPLUG is not set CONFIG_MACH_ICONNECT=y diff --git a/target/linux/kirkwood/files/arch/arm/mach-kirkwood/goflexhome-setup.c b/target/linux/kirkwood/files/arch/arm/mach-kirkwood/goflexhome-setup.c new file mode 100644 index 000000000..84daeefe6 --- /dev/null +++ b/target/linux/kirkwood/files/arch/arm/mach-kirkwood/goflexhome-setup.c @@ -0,0 +1,123 @@ +/* + * arch/arm/mach-kirkwood/goflexhome-setup.c + * + * Seagate GoFlex Home Setup + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/ata_platform.h> +#include <linux/mtd/partitions.h> +#include <linux/mv643xx_eth.h> +#include <linux/gpio.h> +#include <linux/leds.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <mach/kirkwood.h> +#include "common.h" +#include "mpp.h" + +static struct mtd_partition goflexhome_nand_parts[] = { + { + .name = "u-boot", + .offset = 0, + .size = SZ_1M + }, { + .name = "uImage", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_2M + SZ_4M + }, { + .name = "root", + .offset = MTDPART_OFS_NXTBLK, + .size = MTDPART_SIZ_FULL + }, +}; + +static struct mv643xx_eth_platform_data goflexhome_ge00_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(0), +}; + +static struct mv_sata_platform_data goflexhome_sata_data = { + .n_ports = 1, +}; + +static struct gpio_led goflexhome_led_pins[] = { + { + .name = "status:green:health", + .default_trigger = "default-on", + .gpio = 46, + .active_low = 1, + }, + { + .name = "status:orange:fault", + .default_trigger = "none", + .gpio = 47, + .active_low = 1, + }, + { + .name = "status:white:misc", + .default_trigger = "none", + .gpio = 40, + .active_low = 0, + } +}; + +static struct gpio_led_platform_data goflexhome_led_data = { + .leds = goflexhome_led_pins, + .num_leds = ARRAY_SIZE(goflexhome_led_pins), +}; + +static struct platform_device goflexhome_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &goflexhome_led_data, + } +}; + +static unsigned int goflexhome_mpp_config[] __initdata = { + MPP29_GPIO, /* USB Power Enable */ + MPP47_GPIO, /* LED Orange */ + MPP46_GPIO, /* LED Green */ + MPP40_GPIO, /* LED White */ + 0 +}; + +static void __init goflexhome_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_init(); + + /* setup gpio pin select */ + kirkwood_mpp_conf(goflexhome_mpp_config); + + kirkwood_uart0_init(); + kirkwood_nand_init(ARRAY_AND_SIZE(goflexhome_nand_parts), 40); + + if (gpio_request(29, "USB Power Enable") != 0 || + gpio_direction_output(29, 1) != 0) + printk(KERN_ERR "can't set up GPIO 29 (USB Power Enable)\n"); + kirkwood_ehci_init(); + kirkwood_ge00_init(&goflexhome_ge00_data); + kirkwood_sata_init(&goflexhome_sata_data); + + platform_device_register(&goflexhome_leds); +} + +MACHINE_START(GOFLEXHOME, "Seagate GoFlex Home") + /* Maintainer: Peter Carmichael <peterjncarm@ovi.com> */ + .atag_offset = 0x100, + .init_machine = goflexhome_init, + .map_io = kirkwood_map_io, + .init_early = kirkwood_init_early, + .init_irq = kirkwood_init_irq, + .timer = &kirkwood_timer, + .restart = kirkwood_restart, +MACHINE_END diff --git a/target/linux/kirkwood/files/arch/arm/mach-kirkwood/goflexnet-setup.c b/target/linux/kirkwood/files/arch/arm/mach-kirkwood/goflexnet-setup.c new file mode 100644 index 000000000..cd9dc9ef1 --- /dev/null +++ b/target/linux/kirkwood/files/arch/arm/mach-kirkwood/goflexnet-setup.c @@ -0,0 +1,176 @@ +/* + * arch/arm/mach-kirkwood/goflexnet-setup.c + * + * Seagate GoFlex Net Setup + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/ata_platform.h> +#include <linux/mtd/partitions.h> +#include <linux/mv643xx_eth.h> +#include <linux/gpio.h> +#include <linux/leds.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <mach/kirkwood.h> +#include "common.h" +#include "mpp.h" + +static struct mtd_partition goflexnet_nand_parts[] = { + { + .name = "u-boot", + .offset = 0, + .size = SZ_1M + }, { + .name = "uImage", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_4M + }, { + .name = "rootfs", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_32M + }, { + .name = "data", + .offset = MTDPART_OFS_NXTBLK, + .size = MTDPART_SIZ_FULL + }, +}; + +static struct mv643xx_eth_platform_data goflexnet_ge00_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(0), +}; + +static struct mv_sata_platform_data goflexnet_sata_data = { + .n_ports = 2, +}; + +static struct gpio_led goflexnet_led_pins[] = { + { + .name = "status:green:health", + .default_trigger = "default-on", + .gpio = 46, // 0x4000 + .active_low = 1, + }, + { + .name = "status:orange:fault", + .default_trigger = "none", + .gpio = 47, // 0x8000 + .active_low = 1, + }, + { + .name = "status:white:left0", + .default_trigger = "none", + .gpio = 42, // 0x0400 + .active_low = 0, + }, + { + .name = "status:white:left1", + .default_trigger = "none", + .gpio = 43, // 0x0800 + .active_low = 0, + }, + { + .name = "status:white:left2", + .default_trigger = "none", + .gpio = 44, // 0x1000 + .active_low = 0, + }, + { + .name = "status:white:left3", + .default_trigger = "none", + .gpio = 45, // 0x2000 + .active_low = 0, + }, + { + .name = "status:white:right0", + .default_trigger = "none", + .gpio = 38, // 0x0040 + .active_low = 0, + }, + { + .name = "status:white:right1", + .default_trigger = "none", + .gpio = 39, // 0x0080 + .active_low = 0, + }, + { + .name = "status:white:right2", + .default_trigger = "none", + .gpio = 40, // 0x0100 + .active_low = 0, + }, + { + .name = "status:white:right3", + .default_trigger = "none", + .gpio = 41, // 0x0200 + .active_low = 0, + } +}; + +static struct gpio_led_platform_data goflexnet_led_data = { + .leds = goflexnet_led_pins, + .num_leds = ARRAY_SIZE(goflexnet_led_pins), +}; + +static struct platform_device goflexnet_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &goflexnet_led_data, + } +}; + +static unsigned int goflexnet_mpp_config[] __initdata = { + MPP29_GPIO, /* USB Power Enable */ + MPP47_GPIO, /* LED Orange */ + MPP46_GPIO, /* LED Green */ + MPP45_GPIO, /* LED Left Capacity 3 */ + MPP44_GPIO, /* LED Left Capacity 2 */ + MPP43_GPIO, /* LED Left Capacity 1 */ + MPP42_GPIO, /* LED Left Capacity 0 */ + MPP41_GPIO, /* LED Right Capacity 3 */ + MPP40_GPIO, /* LED Right Capacity 2 */ + MPP39_GPIO, /* LED Right Capacity 1 */ + MPP38_GPIO, /* LED Right Capacity 0 */ + 0 +}; + +static void __init goflexnet_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_init(); + + /* setup gpio pin select */ + kirkwood_mpp_conf(goflexnet_mpp_config); + + kirkwood_uart0_init(); + kirkwood_nand_init(ARRAY_AND_SIZE(goflexnet_nand_parts), 40); + + if (gpio_request(29, "USB Power Enable") != 0 || + gpio_direction_output(29, 1) != 0) + printk(KERN_ERR "can't set up GPIO 29 (USB Power Enable)\n"); + kirkwood_ehci_init(); + kirkwood_ge00_init(&goflexnet_ge00_data); + kirkwood_sata_init(&goflexnet_sata_data); + + platform_device_register(&goflexnet_leds); +} + +MACHINE_START(GOFLEXNET, "Seagate GoFlex Net") + /* Maintainer: Peter Carmichael <peterjncarm@ovi.com> */ + .atag_offset = 0x100, + .init_machine = goflexnet_init, + .map_io = kirkwood_map_io, + .init_early = kirkwood_init_early, + .init_irq = kirkwood_init_irq, + .timer = &kirkwood_timer, + .restart = kirkwood_restart, +MACHINE_END diff --git a/target/linux/kirkwood/patches/000-boards.patch b/target/linux/kirkwood/patches/000-boards.patch index 4fe376e9b..22bd2b66b 100644 --- a/target/linux/kirkwood/patches/000-boards.patch +++ b/target/linux/kirkwood/patches/000-boards.patch @@ -1,6 +1,15 @@ --- a/arch/arm/mach-kirkwood/Makefile +++ b/arch/arm/mach-kirkwood/Makefile -@@ -18,5 +18,8 @@ obj-$(CONFIG_MACH_D2NET_V2) += d2net_v2 +@@ -8,6 +8,8 @@ obj-$(CONFIG_MACH_SHEEVAPLUG) += sheeva + obj-$(CONFIG_MACH_ESATA_SHEEVAPLUG) += sheevaplug-setup.o + obj-$(CONFIG_MACH_GURUPLUG) += guruplug-setup.o + obj-$(CONFIG_MACH_DOCKSTAR) += dockstar-setup.o ++obj-$(CONFIG_MACH_GOFLEXNET) += goflexnet-setup.o ++obj-$(CONFIG_MACH_GOFLEXHOME) += goflexhome-setup.o + obj-$(CONFIG_MACH_TS219) += ts219-setup.o tsx1x-common.o + obj-$(CONFIG_MACH_TS41X) += ts41x-setup.o tsx1x-common.o + obj-$(CONFIG_MACH_OPENRD) += openrd-setup.o +@@ -18,5 +20,8 @@ obj-$(CONFIG_MACH_D2NET_V2) += d2net_v2 obj-$(CONFIG_MACH_NET2BIG_V2) += netxbig_v2-setup.o lacie_v2-common.o obj-$(CONFIG_MACH_NET5BIG_V2) += netxbig_v2-setup.o lacie_v2-common.o obj-$(CONFIG_MACH_T5325) += t5325-setup.o @@ -11,7 +20,26 @@ obj-$(CONFIG_CPU_IDLE) += cpuidle.o --- a/arch/arm/mach-kirkwood/Kconfig +++ b/arch/arm/mach-kirkwood/Kconfig -@@ -130,6 +130,24 @@ config MACH_T5325 +@@ -64,6 +64,18 @@ config MACH_DOCKSTAR + Say 'Y' here if you want your kernel to support the + Seagate FreeAgent DockStar. + ++config MACH_GOFLEXNET ++ bool "Seagate GoFlex Net" ++ help ++ Say 'Y' here if you want your kernel to support the ++ Seagate GoFlex Net. ++ ++config MACH_GOFLEXHOME ++ bool "Seagate GoFlex Home" ++ help ++ Say 'Y' here if you want your kernel to support the ++ Seagate GoFlex Home. ++ + config MACH_OPENRD + bool + +@@ -130,6 +142,24 @@ config MACH_T5325 Say 'Y' here if you want your kernel to support the HP t5325 Thin Client. |