diff options
Diffstat (limited to 'target/linux/generic')
8 files changed, 2278 insertions, 298 deletions
diff --git a/target/linux/generic/patches-3.3/020-ssb_update.patch b/target/linux/generic/patches-3.3/020-ssb_update.patch index e427574f7..10c70abbb 100644 --- a/target/linux/generic/patches-3.3/020-ssb_update.patch +++ b/target/linux/generic/patches-3.3/020-ssb_update.patch @@ -100,7 +100,48 @@ +} --- a/drivers/ssb/driver_mipscore.c +++ b/drivers/ssb/driver_mipscore.c -@@ -208,6 +208,9 @@ u32 ssb_cpu_clock(struct ssb_mipscore *m +@@ -190,16 +190,32 @@ static void ssb_mips_flash_detect(struct + { + struct ssb_bus *bus = mcore->dev->bus; + +- mcore->flash_buswidth = 2; +- if (bus->chipco.dev) { +- mcore->flash_window = 0x1c000000; +- mcore->flash_window_size = 0x02000000; ++ /* When there is no chipcommon on the bus there is 4MB flash */ ++ if (!bus->chipco.dev) { ++ mcore->pflash.present = true; ++ mcore->pflash.buswidth = 2; ++ mcore->pflash.window = SSB_FLASH1; ++ mcore->pflash.window_size = SSB_FLASH1_SZ; ++ return; ++ } ++ ++ /* There is ChipCommon, so use it to read info about flash */ ++ switch (bus->chipco.capabilities & SSB_CHIPCO_CAP_FLASHT) { ++ case SSB_CHIPCO_FLASHT_STSER: ++ case SSB_CHIPCO_FLASHT_ATSER: ++ pr_err("Serial flash not supported\n"); ++ break; ++ case SSB_CHIPCO_FLASHT_PARA: ++ pr_debug("Found parallel flash\n"); ++ mcore->pflash.present = true; ++ mcore->pflash.window = SSB_FLASH2; ++ mcore->pflash.window_size = SSB_FLASH2_SZ; + if ((ssb_read32(bus->chipco.dev, SSB_CHIPCO_FLASH_CFG) + & SSB_CHIPCO_CFG_DS16) == 0) +- mcore->flash_buswidth = 1; +- } else { +- mcore->flash_window = 0x1fc00000; +- mcore->flash_window_size = 0x00400000; ++ mcore->pflash.buswidth = 1; ++ else ++ mcore->pflash.buswidth = 2; ++ break; + } + } + +@@ -208,6 +224,9 @@ u32 ssb_cpu_clock(struct ssb_mipscore *m struct ssb_bus *bus = mcore->dev->bus; u32 pll_type, n, m, rate = 0; @@ -673,6 +714,19 @@ /* Vendor-ID values */ #define SSB_VENDOR_BROADCOM 0x4243 +--- a/include/linux/ssb/ssb_driver_chipcommon.h ++++ b/include/linux/ssb/ssb_driver_chipcommon.h +@@ -504,7 +504,9 @@ + #define SSB_CHIPCO_FLASHCTL_ST_SE 0x02D8 /* Sector Erase */ + #define SSB_CHIPCO_FLASHCTL_ST_BE 0x00C7 /* Bulk Erase */ + #define SSB_CHIPCO_FLASHCTL_ST_DP 0x00B9 /* Deep Power-down */ +-#define SSB_CHIPCO_FLASHCTL_ST_RSIG 0x03AB /* Read Electronic Signature */ ++#define SSB_CHIPCO_FLASHCTL_ST_RES 0x03AB /* Read Electronic Signature */ ++#define SSB_CHIPCO_FLASHCTL_ST_CSA 0x1000 /* Keep chip select asserted */ ++#define SSB_CHIPCO_FLASHCTL_ST_SSE 0x0220 /* Sub-sector Erase */ + + /* Status register bits for ST flashes */ + #define SSB_CHIPCO_FLASHSTA_ST_WIP 0x01 /* Write In Progress */ --- a/include/linux/ssb/ssb_driver_gige.h +++ b/include/linux/ssb/ssb_driver_gige.h @@ -2,6 +2,7 @@ @@ -683,6 +737,32 @@ #include <linux/pci.h> #include <linux/spinlock.h> +--- a/include/linux/ssb/ssb_driver_mips.h ++++ b/include/linux/ssb/ssb_driver_mips.h +@@ -13,6 +13,12 @@ struct ssb_serial_port { + unsigned int reg_shift; + }; + ++struct ssb_pflash { ++ bool present; ++ u8 buswidth; ++ u32 window; ++ u32 window_size; ++}; + + struct ssb_mipscore { + struct ssb_device *dev; +@@ -20,9 +26,7 @@ struct ssb_mipscore { + int nr_serial_ports; + struct ssb_serial_port serial_ports[4]; + +- u8 flash_buswidth; +- u32 flash_window; +- u32 flash_window_size; ++ struct ssb_pflash pflash; + }; + + extern void ssb_mipscore_init(struct ssb_mipscore *mcore); --- a/include/linux/ssb/ssb_regs.h +++ b/include/linux/ssb/ssb_regs.h @@ -228,6 +228,7 @@ diff --git a/target/linux/generic/patches-3.3/025-bcma_backport.patch b/target/linux/generic/patches-3.3/025-bcma_backport.patch index 29aaa2958..824c4455c 100644 --- a/target/linux/generic/patches-3.3/025-bcma_backport.patch +++ b/target/linux/generic/patches-3.3/025-bcma_backport.patch @@ -1,3 +1,33 @@ +--- a/arch/mips/bcm47xx/nvram.c ++++ b/arch/mips/bcm47xx/nvram.c +@@ -43,8 +43,8 @@ static void early_nvram_init(void) + #ifdef CONFIG_BCM47XX_SSB + case BCM47XX_BUS_TYPE_SSB: + mcore_ssb = &bcm47xx_bus.ssb.mipscore; +- base = mcore_ssb->flash_window; +- lim = mcore_ssb->flash_window_size; ++ base = mcore_ssb->pflash.window; ++ lim = mcore_ssb->pflash.window_size; + break; + #endif + #ifdef CONFIG_BCM47XX_BCMA +--- a/arch/mips/bcm47xx/wgt634u.c ++++ b/arch/mips/bcm47xx/wgt634u.c +@@ -156,10 +156,10 @@ static int __init wgt634u_init(void) + SSB_CHIPCO_IRQ_GPIO); + } + +- wgt634u_flash_data.width = mcore->flash_buswidth; +- wgt634u_flash_resource.start = mcore->flash_window; +- wgt634u_flash_resource.end = mcore->flash_window +- + mcore->flash_window_size ++ wgt634u_flash_data.width = mcore->pflash.buswidth; ++ wgt634u_flash_resource.start = mcore->pflash.window; ++ wgt634u_flash_resource.end = mcore->pflash.window ++ + mcore->pflash.window_size + - 1; + return platform_add_devices(wgt634u_devices, + ARRAY_SIZE(wgt634u_devices)); --- a/drivers/bcma/Kconfig +++ b/drivers/bcma/Kconfig @@ -29,7 +29,7 @@ config BCMA_HOST_PCI @@ -9,10 +39,20 @@ help PCI core hostmode operation (external PCI bus). -@@ -46,6 +46,15 @@ config BCMA_DRIVER_MIPS +@@ -46,6 +46,25 @@ config BCMA_DRIVER_MIPS If unsure, say N ++config BCMA_SFLASH ++ bool ++ depends on BCMA_DRIVER_MIPS ++ default y ++ ++config BCMA_NFLASH ++ bool ++ depends on BCMA_DRIVER_MIPS ++ default y ++ +config BCMA_DRIVER_GMAC_CMN + bool "BCMA Broadcom GBIT MAC COMMON core driver" + depends on BCMA @@ -27,7 +67,11 @@ depends on BCMA --- a/drivers/bcma/Makefile +++ b/drivers/bcma/Makefile -@@ -3,6 +3,7 @@ bcma-y += driver_chipcommon.o driver +@@ -1,8 +1,11 @@ + bcma-y += main.o scan.o core.o sprom.o + bcma-y += driver_chipcommon.o driver_chipcommon_pmu.o ++bcma-$(CONFIG_BCMA_SFLASH) += driver_chipcommon_sflash.o ++bcma-$(CONFIG_BCMA_NFLASH) += driver_chipcommon_nflash.o bcma-y += driver_pci.o bcma-$(CONFIG_BCMA_DRIVER_PCI_HOSTMODE) += driver_pci_host.o bcma-$(CONFIG_BCMA_DRIVER_MIPS) += driver_mips.o @@ -58,7 +102,37 @@ void bcma_bus_unregister(struct bcma_bus *bus); int __init bcma_bus_early_register(struct bcma_bus *bus, struct bcma_device *core_cc, -@@ -48,8 +57,12 @@ extern int __init bcma_host_pci_init(voi +@@ -42,14 +51,42 @@ void bcma_chipco_serial_init(struct bcma + u32 bcma_pmu_alp_clock(struct bcma_drv_cc *cc); + u32 bcma_pmu_get_clockcpu(struct bcma_drv_cc *cc); + ++#ifdef CONFIG_BCMA_SFLASH ++/* driver_chipcommon_sflash.c */ ++int bcma_sflash_init(struct bcma_drv_cc *cc); ++extern struct platform_device bcma_sflash_dev; ++#else ++static inline int bcma_sflash_init(struct bcma_drv_cc *cc) ++{ ++ bcma_err(cc->core->bus, "Serial flash not supported\n"); ++ return 0; ++} ++#endif /* CONFIG_BCMA_SFLASH */ ++ ++#ifdef CONFIG_BCMA_NFLASH ++/* driver_chipcommon_nflash.c */ ++int bcma_nflash_init(struct bcma_drv_cc *cc); ++extern struct platform_device bcma_nflash_dev; ++#else ++static inline int bcma_nflash_init(struct bcma_drv_cc *cc) ++{ ++ bcma_err(cc->core->bus, "NAND flash not supported\n"); ++ return 0; ++} ++#endif /* CONFIG_BCMA_NFLASH */ ++ + #ifdef CONFIG_BCMA_HOST_PCI + /* host_pci.c */ + extern int __init bcma_host_pci_init(void); extern void __exit bcma_host_pci_exit(void); #endif /* CONFIG_BCMA_HOST_PCI */ @@ -82,6 +156,15 @@ udelay(1); } EXPORT_SYMBOL_GPL(bcma_core_disable); +@@ -64,7 +65,7 @@ void bcma_core_set_clockmode(struct bcma + switch (clkmode) { + case BCMA_CLKMODE_FAST: + bcma_set32(core, BCMA_CLKCTLST, BCMA_CLKCTLST_FORCEHT); +- udelay(64); ++ usleep_range(64, 300); + for (i = 0; i < 1500; i++) { + if (bcma_read32(core, BCMA_CLKCTLST) & + BCMA_CLKCTLST_HAVEHT) { @@ -74,10 +75,10 @@ void bcma_core_set_clockmode(struct bcma udelay(10); } @@ -120,7 +203,45 @@ } --- a/drivers/bcma/driver_chipcommon.c +++ b/drivers/bcma/driver_chipcommon.c -@@ -44,7 +44,7 @@ void bcma_core_chipcommon_init(struct bc +@@ -22,12 +22,9 @@ static inline u32 bcma_cc_write32_masked + return value; + } + +-void bcma_core_chipcommon_init(struct bcma_drv_cc *cc) ++void bcma_core_chipcommon_early_init(struct bcma_drv_cc *cc) + { +- u32 leddc_on = 10; +- u32 leddc_off = 90; +- +- if (cc->setup_done) ++ if (cc->early_setup_done) + return; + + if (cc->core->id.rev >= 11) +@@ -36,6 +33,22 @@ void bcma_core_chipcommon_init(struct bc + if (cc->core->id.rev >= 35) + cc->capabilities_ext = bcma_cc_read32(cc, BCMA_CC_CAP_EXT); + ++ if (cc->capabilities & BCMA_CC_CAP_PMU) ++ bcma_pmu_early_init(cc); ++ ++ cc->early_setup_done = true; ++} ++ ++void bcma_core_chipcommon_init(struct bcma_drv_cc *cc) ++{ ++ u32 leddc_on = 10; ++ u32 leddc_off = 90; ++ ++ if (cc->setup_done) ++ return; ++ ++ bcma_core_chipcommon_early_init(cc); ++ + if (cc->core->id.rev >= 20) { + bcma_cc_write32(cc, BCMA_CC_GPIOPULLUP, 0); + bcma_cc_write32(cc, BCMA_CC_GPIOPULLDOWN, 0); +@@ -44,7 +57,7 @@ void bcma_core_chipcommon_init(struct bc if (cc->capabilities & BCMA_CC_CAP_PMU) bcma_pmu_init(cc); if (cc->capabilities & BCMA_CC_CAP_PCTL) @@ -129,7 +250,7 @@ if (cc->core->id.rev >= 16) { if (cc->core->bus->sprom.leddc_on_time && -@@ -137,8 +137,7 @@ void bcma_chipco_serial_init(struct bcma +@@ -137,8 +150,7 @@ void bcma_chipco_serial_init(struct bcma | BCMA_CC_CORECTL_UARTCLKEN); } } else { @@ -139,6 +260,53 @@ return; } +--- /dev/null ++++ b/drivers/bcma/driver_chipcommon_nflash.c +@@ -0,0 +1,44 @@ ++/* ++ * Broadcom specific AMBA ++ * ChipCommon NAND flash interface ++ * ++ * Licensed under the GNU/GPL. See COPYING for details. ++ */ ++ ++#include <linux/platform_device.h> ++#include <linux/bcma/bcma.h> ++ ++#include "bcma_private.h" ++ ++struct platform_device bcma_nflash_dev = { ++ .name = "bcma_nflash", ++ .num_resources = 0, ++}; ++ ++/* Initialize NAND flash access */ ++int bcma_nflash_init(struct bcma_drv_cc *cc) ++{ ++ struct bcma_bus *bus = cc->core->bus; ++ ++ if (bus->chipinfo.id != BCMA_CHIP_ID_BCM4706 && ++ cc->core->id.rev != 0x38) { ++ bcma_err(bus, "NAND flash on unsupported board!\n"); ++ return -ENOTSUPP; ++ } ++ ++ if (!(cc->capabilities & BCMA_CC_CAP_NFLASH)) { ++ bcma_err(bus, "NAND flash not present according to ChipCommon\n"); ++ return -ENODEV; ++ } ++ ++ cc->nflash.present = true; ++ if (cc->core->id.rev == 38 && ++ (cc->status & BCMA_CC_CHIPST_5357_NAND_BOOT)) ++ cc->nflash.boot = true; ++ ++ /* Prepare platform device, but don't register it yet. It's too early, ++ * malloc (required by device_private_init) is not available yet. */ ++ bcma_nflash_dev.dev.platform_data = &cc->nflash; ++ ++ return 0; ++} --- a/drivers/bcma/driver_chipcommon_pmu.c +++ b/drivers/bcma/driver_chipcommon_pmu.c @@ -3,7 +3,8 @@ @@ -193,7 +361,7 @@ } /* Set the resource masks. */ -@@ -93,22 +75,9 @@ static void bcma_pmu_resources_init(stru +@@ -93,22 +75,12 @@ static void bcma_pmu_resources_init(stru bcma_cc_write32(cc, BCMA_CC_PMU_MINRES_MSK, min_msk); if (max_msk) bcma_cc_write32(cc, BCMA_CC_PMU_MAXRES_MSK, max_msk); @@ -213,12 +381,15 @@ - pr_err("PMU switch/regulators init unknown for device " - "0x%04X\n", bus->chipinfo.id); - } -+ /* Add some delay; allow resources to come up and settle. */ ++ /* ++ * Add some delay; allow resources to come up and settle. ++ * Delay is required for SoC (early init). ++ */ + mdelay(2); } /* Disable to allow reading SPROM. Don't know the adventages of enabling it. */ -@@ -122,8 +91,11 @@ void bcma_chipco_bcm4331_ext_pa_lines_ct +@@ -122,51 +94,69 @@ void bcma_chipco_bcm4331_ext_pa_lines_ct val |= BCMA_CHIPCTL_4331_EXTPA_EN; if (bus->chipinfo.pkg == 9 || bus->chipinfo.pkg == 11) val |= BCMA_CHIPCTL_4331_EXTPA_ON_GPIO2_5; @@ -230,7 +401,11 @@ val &= ~BCMA_CHIPCTL_4331_EXTPA_ON_GPIO2_5; } bcma_cc_write32(cc, BCMA_CC_CHIPCTL, val); -@@ -134,26 +106,38 @@ void bcma_pmu_workarounds(struct bcma_dr + } + +-void bcma_pmu_workarounds(struct bcma_drv_cc *cc) ++static void bcma_pmu_workarounds(struct bcma_drv_cc *cc) + { struct bcma_bus *bus = cc->core->bus; switch (bus->chipinfo.id) { @@ -240,7 +415,7 @@ + /* enable 12 mA drive strenth for 4313 and set chipControl + register bit 1 */ + bcma_chipco_chipctl_maskset(cc, 0, -+ BCMA_CCTRL_4313_12MA_LED_DRIVE, ++ ~BCMA_CCTRL_4313_12MA_LED_DRIVE, + BCMA_CCTRL_4313_12MA_LED_DRIVE); break; - case 0x4331: @@ -260,15 +435,15 @@ - "implemented\n"); - bcma_chipco_chipctl_maskset(cc, 0, ~0, 0x00F000F0); + bcma_cc_maskset32(cc, BCMA_CC_CHIPCTL, -+ BCMA_CCTRL_43224_GPIO_TOGGLE, ++ ~BCMA_CCTRL_43224_GPIO_TOGGLE, + BCMA_CCTRL_43224_GPIO_TOGGLE); + bcma_chipco_chipctl_maskset(cc, 0, -+ BCMA_CCTRL_43224A0_12MA_LED_DRIVE, ++ ~BCMA_CCTRL_43224A0_12MA_LED_DRIVE, + BCMA_CCTRL_43224A0_12MA_LED_DRIVE); } else { - bcma_chipco_chipctl_maskset(cc, 0, ~0, 0xF0); + bcma_chipco_chipctl_maskset(cc, 0, -+ BCMA_CCTRL_43224B0_12MA_LED_DRIVE, ++ ~BCMA_CCTRL_43224B0_12MA_LED_DRIVE, + BCMA_CCTRL_43224B0_12MA_LED_DRIVE); } break; @@ -282,7 +457,11 @@ } } -@@ -164,8 +148,8 @@ void bcma_pmu_init(struct bcma_drv_cc *c +-void bcma_pmu_init(struct bcma_drv_cc *cc) ++void bcma_pmu_early_init(struct bcma_drv_cc *cc) + { + u32 pmucap; + pmucap = bcma_cc_read32(cc, BCMA_CC_PMU_CAP); cc->pmu.rev = (pmucap & BCMA_CC_PMU_CAP_REVISION); @@ -290,10 +469,14 @@ - pmucap); + bcma_debug(cc->core->bus, "Found rev %u PMU (capabilities 0x%08X)\n", + cc->pmu.rev, pmucap); ++} ++void bcma_pmu_init(struct bcma_drv_cc *cc) ++{ if (cc->pmu.rev == 1) bcma_cc_mask32(cc, BCMA_CC_PMU_CTL, -@@ -174,12 +158,7 @@ void bcma_pmu_init(struct bcma_drv_cc *c + ~BCMA_CC_PMU_CTL_NOILPONW); +@@ -174,12 +164,7 @@ void bcma_pmu_init(struct bcma_drv_cc *c bcma_cc_set32(cc, BCMA_CC_PMU_CTL, BCMA_CC_PMU_CTL_NOILPONW); @@ -306,7 +489,7 @@ bcma_pmu_workarounds(cc); } -@@ -188,23 +167,22 @@ u32 bcma_pmu_alp_clock(struct bcma_drv_c +@@ -188,23 +173,22 @@ u32 bcma_pmu_alp_clock(struct bcma_drv_c struct bcma_bus *bus = cc->core->bus; switch (bus->chipinfo.id) { @@ -341,7 +524,7 @@ } return BCMA_CC_PMU_ALP_CLOCK; } -@@ -221,7 +199,8 @@ static u32 bcma_pmu_clock(struct bcma_dr +@@ -221,7 +205,8 @@ static u32 bcma_pmu_clock(struct bcma_dr BUG_ON(!m || m > 4); @@ -351,7 +534,7 @@ /* Detect failure in clock setting */ tmp = bcma_cc_read32(cc, BCMA_CC_CHIPSTAT); if (tmp & 0x40000) -@@ -247,33 +226,62 @@ static u32 bcma_pmu_clock(struct bcma_dr +@@ -247,33 +232,62 @@ static u32 bcma_pmu_clock(struct bcma_dr return (fc / div) * 1000000; } @@ -386,7 +569,8 @@ +} + /* query bus clock frequency for PMU-enabled chipcommon */ - u32 bcma_pmu_get_clockcontrol(struct bcma_drv_cc *cc) +-u32 bcma_pmu_get_clockcontrol(struct bcma_drv_cc *cc) ++static u32 bcma_pmu_get_clockcontrol(struct bcma_drv_cc *cc) { struct bcma_bus *bus = cc->core->bus; @@ -427,7 +611,7 @@ } return BCMA_CC_PMU_HT_CLOCK; } -@@ -283,17 +291,21 @@ u32 bcma_pmu_get_clockcpu(struct bcma_dr +@@ -283,17 +297,21 @@ u32 bcma_pmu_get_clockcpu(struct bcma_dr { struct bcma_bus *bus = cc->core->bus; @@ -453,7 +637,7 @@ pll = BCMA_CC_PMU5357_MAINPLL_PLL0; break; default: -@@ -301,10 +313,188 @@ u32 bcma_pmu_get_clockcpu(struct bcma_dr +@@ -301,10 +319,188 @@ u32 bcma_pmu_get_clockcpu(struct bcma_dr break; } @@ -645,6 +829,174 @@ +} +EXPORT_SYMBOL_GPL(bcma_pmu_spuravoid_pllupdate); --- /dev/null ++++ b/drivers/bcma/driver_chipcommon_sflash.c +@@ -0,0 +1,165 @@ ++/* ++ * Broadcom specific AMBA ++ * ChipCommon serial flash interface ++ * ++ * Licensed under the GNU/GPL. See COPYING for details. ++ */ ++ ++#include <linux/platform_device.h> ++#include <linux/bcma/bcma.h> ++ ++#include "bcma_private.h" ++ ++static struct resource bcma_sflash_resource = { ++ .name = "bcma_sflash", ++ .start = BCMA_SOC_FLASH2, ++ .end = 0, ++ .flags = IORESOURCE_MEM | IORESOURCE_READONLY, ++}; ++ ++struct platform_device bcma_sflash_dev = { ++ .name = "bcma_sflash", ++ .resource = &bcma_sflash_resource, ++ .num_resources = 1, ++}; ++ ++struct bcma_sflash_tbl_e { ++ char *name; ++ u32 id; ++ u32 blocksize; ++ u16 numblocks; ++}; ++ ++static struct bcma_sflash_tbl_e bcma_sflash_st_tbl[] = { ++ { "M25P20", 0x11, 0x10000, 4, }, ++ { "M25P40", 0x12, 0x10000, 8, }, ++ ++ { "M25P16", 0x14, 0x10000, 32, }, ++ { "M25P32", 0x14, 0x10000, 64, }, ++ { "M25P64", 0x16, 0x10000, 128, }, ++ { "M25FL128", 0x17, 0x10000, 256, }, ++ { 0 }, ++}; ++ ++static struct bcma_sflash_tbl_e bcma_sflash_sst_tbl[] = { ++ { "SST25WF512", 1, 0x1000, 16, }, ++ { "SST25VF512", 0x48, 0x1000, 16, }, ++ { "SST25WF010", 2, 0x1000, 32, }, ++ { "SST25VF010", 0x49, 0x1000, 32, }, ++ { "SST25WF020", 3, 0x1000, 64, }, ++ { "SST25VF020", 0x43, 0x1000, 64, }, ++ { "SST25WF040", 4, 0x1000, 128, }, ++ { "SST25VF040", 0x44, 0x1000, 128, }, ++ { "SST25VF040B", 0x8d, 0x1000, 128, }, ++ { "SST25WF080", 5, 0x1000, 256, }, ++ { "SST25VF080B", 0x8e, 0x1000, 256, }, ++ { "SST25VF016", 0x41, 0x1000, 512, }, ++ { "SST25VF032", 0x4a, 0x1000, 1024, }, ++ { "SST25VF064", 0x4b, 0x1000, 2048, }, ++ { 0 }, ++}; ++ ++static struct bcma_sflash_tbl_e bcma_sflash_at_tbl[] = { ++ { "AT45DB011", 0xc, 256, 512, }, ++ { "AT45DB021", 0x14, 256, 1024, }, ++ { "AT45DB041", 0x1c, 256, 2048, }, ++ { "AT45DB081", 0x24, 256, 4096, }, ++ { "AT45DB161", 0x2c, 512, 4096, }, ++ { "AT45DB321", 0x34, 512, 8192, }, ++ { "AT45DB642", 0x3c, 1024, 8192, }, ++ { 0 }, ++}; ++ ++static void bcma_sflash_cmd(struct bcma_drv_cc *cc, u32 opcode) ++{ ++ int i; ++ bcma_cc_write32(cc, BCMA_CC_FLASHCTL, ++ BCMA_CC_FLASHCTL_START | opcode); ++ for (i = 0; i < 1000; i++) { ++ if (!(bcma_cc_read32(cc, BCMA_CC_FLASHCTL) & ++ BCMA_CC_FLASHCTL_BUSY)) ++ return; ++ cpu_relax(); ++ } ++ bcma_err(cc->core->bus, "SFLASH control command failed (timeout)!\n"); ++} ++ ++/* Initialize serial flash access */ ++int bcma_sflash_init(struct bcma_drv_cc *cc) ++{ ++ struct bcma_bus *bus = cc->core->bus; ++ struct bcma_sflash *sflash = &cc->sflash; ++ struct bcma_sflash_tbl_e *e; ++ u32 id, id2; ++ ++ switch (cc->capabilities & BCMA_CC_CAP_FLASHT) { ++ case BCMA_CC_FLASHT_STSER: ++ bcma_sflash_cmd(cc, BCMA_CC_FLASHCTL_ST_DP); ++ ++ bcma_cc_write32(cc, BCMA_CC_FLASHADDR, 0); ++ bcma_sflash_cmd(cc, BCMA_CC_FLASHCTL_ST_RES); ++ id = bcma_cc_read32(cc, BCMA_CC_FLASHDATA); ++ ++ bcma_cc_write32(cc, BCMA_CC_FLASHADDR, 1); ++ bcma_sflash_cmd(cc, BCMA_CC_FLASHCTL_ST_RES); ++ id2 = bcma_cc_read32(cc, BCMA_CC_FLASHDATA); ++ ++ switch (id) { ++ case 0xbf: ++ for (e = bcma_sflash_sst_tbl; e->name; e++) { ++ if (e->id == id2) ++ break; ++ } ++ break; ++ case 0x13: ++ return -ENOTSUPP; ++ default: ++ for (e = bcma_sflash_st_tbl; e->name; e++) { ++ if (e->id == id) ++ break; ++ } ++ break; ++ } ++ if (!e->name) { ++ bcma_err(bus, "Unsupported ST serial flash (id: 0x%X, id2: 0x%X)\n", id, id2); ++ return -ENOTSUPP; ++ } ++ ++ break; ++ case BCMA_CC_FLASHT_ATSER: ++ bcma_sflash_cmd(cc, BCMA_CC_FLASHCTL_AT_STATUS); ++ id = bcma_cc_read32(cc, BCMA_CC_FLASHDATA) & 0x3c; ++ ++ for (e = bcma_sflash_at_tbl; e->name; e++) { ++ if (e->id == id) ++ break; ++ } ++ if (!e->name) { ++ bcma_err(bus, "Unsupported Atmel serial flash (id: 0x%X)\n", id); ++ return -ENOTSUPP; ++ } ++ ++ break; ++ default: ++ bcma_err(bus, "Unsupported flash type\n"); ++ return -ENOTSUPP; ++ } ++ ++ sflash->window = BCMA_SOC_FLASH2; ++ sflash->blocksize = e->blocksize; ++ sflash->numblocks = e->numblocks; ++ sflash->size = sflash->blocksize * sflash->numblocks; ++ sflash->present = true; ++ ++ bcma_info(bus, "Found %s serial flash (size: %dKiB, blocksize: 0x%X, blocks: %d)\n", ++ e->name, sflash->size / 1024, sflash->blocksize, ++ sflash->numblocks); ++ ++ /* Prepare platform device, but don't register it yet. It's too early, ++ * malloc (required by device_private_init) is not available yet. */ ++ bcma_sflash_dev.resource[0].end = bcma_sflash_dev.resource[0].start + ++ sflash->size; ++ bcma_sflash_dev.dev.platform_data = sflash; ++ ++ return 0; ++} +--- /dev/null +++ b/drivers/bcma/driver_gmac_cmn.c @@ -0,0 +1,14 @@ +/* @@ -683,6 +1035,15 @@ dev->bus->chipinfo.pkg == 11 && dev->id.id == BCMA_CORE_USB20_HOST; } +@@ -131,7 +131,7 @@ static void bcma_core_mips_set_irq(struc + /* backplane irq line is in use, find out who uses + * it and set user to irq 0 + */ +- list_for_each_entry_reverse(core, &bus->cores, list) { ++ list_for_each_entry(core, &bus->cores, list) { + if ((1 << bcma_core_mips_irqflag(core)) == + oldirqflag) { + bcma_core_mips_set_irq(core, 0); @@ -143,8 +143,8 @@ static void bcma_core_mips_set_irq(struc 1 << irqflag); } @@ -694,6 +1055,15 @@ } static void bcma_core_mips_print_irq(struct bcma_device *dev, unsigned int irq) +@@ -161,7 +161,7 @@ static void bcma_core_mips_dump_irq(stru + { + struct bcma_device *core; + +- list_for_each_entry_reverse(core, &bus->cores, list) { ++ list_for_each_entry(core, &bus->cores, list) { + bcma_core_mips_print_irq(core, bcma_core_mips_irq(core)); + } + } @@ -173,7 +173,7 @@ u32 bcma_cpu_clock(struct bcma_drv_mips if (bus->drv_cc.capabilities & BCMA_CC_CAP_PMU) return bcma_pmu_get_clockcpu(&bus->drv_cc); @@ -703,38 +1073,89 @@ return 0; } EXPORT_SYMBOL(bcma_cpu_clock); -@@ -185,10 +185,10 @@ static void bcma_core_mips_flash_detect( - switch (bus->drv_cc.capabilities & BCMA_CC_CAP_FLASHT) { +@@ -181,26 +181,50 @@ EXPORT_SYMBOL(bcma_cpu_clock); + static void bcma_core_mips_flash_detect(struct bcma_drv_mips *mcore) + { + struct bcma_bus *bus = mcore->core->bus; ++ struct bcma_drv_cc *cc = &bus->drv_cc; + +- switch (bus->drv_cc.capabilities & BCMA_CC_CAP_FLASHT) { ++ switch (cc->capabilities & BCMA_CC_CAP_FLASHT) { case BCMA_CC_FLASHT_STSER: case BCMA_CC_FLASHT_ATSER: - pr_err("Serial flash not supported.\n"); -+ bcma_err(bus, "Serial flash not supported.\n"); ++ bcma_debug(bus, "Found serial flash\n"); ++ bcma_sflash_init(cc); break; case BCMA_CC_FLASHT_PARA: - pr_info("found parallel flash.\n"); -+ bcma_info(bus, "found parallel flash.\n"); - bus->drv_cc.pflash.window = 0x1c000000; - bus->drv_cc.pflash.window_size = 0x02000000; - -@@ -199,7 +199,7 @@ static void bcma_core_mips_flash_detect( - bus->drv_cc.pflash.buswidth = 2; +- bus->drv_cc.pflash.window = 0x1c000000; +- bus->drv_cc.pflash.window_size = 0x02000000; ++ bcma_debug(bus, "Found parallel flash\n"); ++ cc->pflash.present = true; ++ cc->pflash.window = BCMA_SOC_FLASH2; ++ cc->pflash.window_size = BCMA_SOC_FLASH2_SZ; + +- if ((bcma_read32(bus->drv_cc.core, BCMA_CC_FLASH_CFG) & ++ if ((bcma_read32(cc->core, BCMA_CC_FLASH_CFG) & + BCMA_CC_FLASH_CFG_DS) == 0) +- bus->drv_cc.pflash.buswidth = 1; ++ cc->pflash.buswidth = 1; + else +- bus->drv_cc.pflash.buswidth = 2; ++ cc->pflash.buswidth = 2; break; default: - pr_err("flash not supported.\n"); -+ bcma_err(bus, "flash not supported.\n"); ++ bcma_err(bus, "Flash type not supported\n"); } ++ ++ if (cc->core->id.rev == 38 || ++ bus->chipinfo.id == BCMA_CHIP_ID_BCM4706) { ++ if (cc->capabilities & BCMA_CC_CAP_NFLASH) { ++ bcma_debug(bus, "Found NAND flash\n"); ++ bcma_nflash_init(cc); ++ } ++ } ++} ++ ++void bcma_core_mips_early_init(struct bcma_drv_mips *mcore) ++{ ++ struct bcma_bus *bus = mcore->core->bus; ++ ++ if (mcore->early_setup_done) ++ return; ++ ++ bcma_chipco_serial_init(&bus->drv_cc); ++ bcma_core_mips_flash_detect(mcore); ++ ++ mcore->early_setup_done = true; } -@@ -209,7 +209,7 @@ void bcma_core_mips_init(struct bcma_drv + void bcma_core_mips_init(struct bcma_drv_mips *mcore) +@@ -209,13 +233,17 @@ void bcma_core_mips_init(struct bcma_drv struct bcma_device *core; bus = mcore->core->bus; - pr_info("Initializing MIPS core...\n"); ++ if (mcore->setup_done) ++ return; ++ + bcma_info(bus, "Initializing MIPS core...\n"); ++ ++ bcma_core_mips_early_init(mcore); + +- if (!mcore->setup_done) +- mcore->assigned_irqs = 1; ++ mcore->assigned_irqs = 1; - if (!mcore->setup_done) - mcore->assigned_irqs = 1; -@@ -244,7 +244,7 @@ void bcma_core_mips_init(struct bcma_drv + /* Assign IRQs to all cores on the bus */ +- list_for_each_entry_reverse(core, &bus->cores, list) { ++ list_for_each_entry(core, &bus->cores, list) { + int mips_irq; + if (core->irq) + continue; +@@ -244,13 +272,8 @@ void bcma_core_mips_init(struct bcma_drv break; } } @@ -742,7 +1163,13 @@ + bcma_info(bus, "IRQ reconfiguration done\n"); bcma_core_mips_dump_irq(bus); - if (mcore->setup_done) +- if (mcore->setup_done) +- return; +- +- bcma_chipco_serial_init(&bus->drv_cc); +- bcma_core_mips_flash_detect(mcore); + mcore->setup_done = true; + } --- a/drivers/bcma/driver_pci.c +++ b/drivers/bcma/driver_pci.c @@ -2,8 +2,9 @@ @@ -756,7 +1183,7 @@ * * Licensed under the GNU/GPL. See COPYING for details. */ -@@ -16,40 +17,39 @@ +@@ -16,120 +17,124 @@ * R/W ops. **************************************************/ @@ -812,9 +1239,10 @@ + v = pcicore_read32(pc, BCMA_CORE_PCI_MDIO_CONTROL); + if (v & BCMA_CORE_PCI_MDIOCTL_ACCESS_DONE) break; - msleep(1); +- msleep(1); ++ usleep_range(1000, 2000); } -@@ -57,79 +57,84 @@ static void bcma_pcie_mdio_set_phy(struc + } static u16 bcma_pcie_mdio_read(struct bcma_drv_pci *pc, u8 device, u8 address) { @@ -868,7 +1296,8 @@ + ret = pcicore_read32(pc, BCMA_CORE_PCI_MDIO_DATA); break; } - msleep(1); +- msleep(1); ++ usleep_range(1000, 2000); } - pcicore_write32(pc, mdio_control, 0); + pcicore_write32(pc, BCMA_CORE_PCI_MDIO_CONTROL, 0); @@ -923,7 +1352,8 @@ + v = pcicore_read32(pc, BCMA_CORE_PCI_MDIO_CONTROL); + if (v & BCMA_CORE_PCI_MDIOCTL_ACCESS_DONE) break; - msleep(1); +- msleep(1); ++ usleep_range(1000, 2000); } - pcicore_write32(pc, mdio_control, 0); + pcicore_write32(pc, BCMA_CORE_PCI_MDIO_CONTROL, 0); @@ -1103,7 +1533,7 @@ +EXPORT_SYMBOL_GPL(bcma_core_pci_extend_L1timer); --- a/drivers/bcma/driver_pci_host.c +++ b/drivers/bcma/driver_pci_host.c -@@ -2,13 +2,592 @@ +@@ -2,13 +2,596 @@ * Broadcom specific AMBA * PCI Core in hostmode * @@ -1140,11 +1570,6 @@ + chipid_top != 0x5300) + return false; + -+ if (bus->sprom.boardflags_lo & BCMA_CORE_PCI_BFL_NOPCI) { -+ bcma_info(bus, "This PCI core is disabled and not working\n"); -+ return false; -+ } -+ + bcma_core_enable(pc->core, 0); + + return !mips_busprobe32(tmp, pc->core->io_addr); @@ -1503,6 +1928,11 @@ + + bcma_info(bus, "PCIEcore in host mode found\n"); + ++ if (bus->sprom.boardflags_lo & BCMA_CORE_PCI_BFL_NOPCI) { ++ bcma_info(bus, "This PCIE core is disabled and not working\n"); ++ return; ++ } ++ + pc_host = kzalloc(sizeof(*pc_host), GFP_KERNEL); + if (!pc_host) { + bcma_err(bus, "can not allocate memory"); @@ -1532,9 +1962,9 @@ + pc_host->io_resource.flags = IORESOURCE_IO | IORESOURCE_PCI_FIXED; + + /* Reset RC */ -+ udelay(3000); ++ usleep_range(3000, 5000); + pcicore_write32(pc, BCMA_CORE_PCI_CTL, BCMA_CORE_PCI_CTL_RST_OE); -+ udelay(1000); ++ usleep_range(1000, 2000); + pcicore_write32(pc, BCMA_CORE_PCI_CTL, BCMA_CORE_PCI_CTL_RST | + BCMA_CORE_PCI_CTL_RST_OE); + @@ -1559,6 +1989,8 @@ + pc_host->mem_resource.start = BCMA_SOC_PCI_MEM; + pc_host->mem_resource.end = BCMA_SOC_PCI_MEM + + BCMA_SOC_PCI_MEM_SZ - 1; ++ pc_host->io_resource.start = 0x100; ++ pc_host->io_resource.end = 0x47F; + pci_membase_1G = BCMA_SOC_PCIE_DMA_H32; + pcicore_write32(pc, BCMA_CORE_PCI_SBTOPCI0, + tmp | BCMA_SOC_PCI_MEM); @@ -1566,6 +1998,8 @@ + pc_host->mem_resource.start = BCMA_SOC_PCI1_MEM; + pc_host->mem_resource.end = BCMA_SOC_PCI1_MEM + + BCMA_SOC_PCI_MEM_SZ - 1; ++ pc_host->io_resource.start = 0x480; ++ pc_host->io_resource.end = 0x7FF; + pci_membase_1G = BCMA_SOC_PCIE1_DMA_H32; + pc_host->host_cfg_addr = BCMA_SOC_PCI1_CFG; + pcicore_write32(pc, BCMA_CORE_PCI_SBTOPCI0, @@ -1588,7 +2022,7 @@ + * before issuing configuration requests to PCI Express + * devices. + */ -+ udelay(100000); ++ msleep(100); + + bcma_core_pci_enable_crs(pc); + @@ -1608,7 +2042,7 @@ + set_io_port_base(pc_host->pci_controller.io_map_base); + /* Give some time to the PCI controller to configure itself with the new + * values. Not waiting at this point causes crashes of the machine. */ -+ mdelay(10); ++ usleep_range(10000, 15000); + register_pci_controller(&pc_host->pci_controller); + return; +} @@ -1709,7 +2143,39 @@ } /* Provides access to the requested core. Returns base offset that has to be -@@ -154,8 +154,8 @@ const struct bcma_host_ops bcma_host_pci +@@ -77,8 +77,8 @@ static void bcma_host_pci_write32(struct + } + + #ifdef CONFIG_BCMA_BLOCKIO +-void bcma_host_pci_block_read(struct bcma_device *core, void *buffer, +- size_t count, u16 offset, u8 reg_width) ++static void bcma_host_pci_block_read(struct bcma_device *core, void *buffer, ++ size_t count, u16 offset, u8 reg_width) + { + void __iomem *addr = core->bus->mmio + offset; + if (core->bus->mapped_core != core) +@@ -100,8 +100,9 @@ void bcma_host_pci_block_read(struct bcm + } + } + +-void bcma_host_pci_block_write(struct bcma_device *core, const void *buffer, +- size_t count, u16 offset, u8 reg_width) ++static void bcma_host_pci_block_write(struct bcma_device *core, ++ const void *buffer, size_t count, ++ u16 offset, u8 reg_width) + { + void __iomem *addr = core->bus->mmio + offset; + if (core->bus->mapped_core != core) +@@ -139,7 +140,7 @@ static void bcma_host_pci_awrite32(struc + iowrite32(value, core->bus->mmio + (1 * BCMA_CORE_SIZE) + offset); + } + +-const struct bcma_host_ops bcma_host_pci_ops = { ++static const struct bcma_host_ops bcma_host_pci_ops = { + .read8 = bcma_host_pci_read8, + .read16 = bcma_host_pci_read16, + .read32 = bcma_host_pci_read32, +@@ -154,8 +155,8 @@ const struct bcma_host_ops bcma_host_pci .awrite32 = bcma_host_pci_awrite32, }; @@ -1720,7 +2186,7 @@ { struct bcma_bus *bus; int err = -ENOMEM; -@@ -188,7 +188,7 @@ static int bcma_host_pci_probe(struct pc +@@ -188,7 +189,7 @@ static int bcma_host_pci_probe(struct pc /* SSB needed additional powering up, do we have any AMBA PCI cards? */ if (!pci_is_pcie(dev)) @@ -1729,7 +2195,7 @@ /* Map MMIO */ err = -ENOMEM; -@@ -201,6 +201,9 @@ static int bcma_host_pci_probe(struct pc +@@ -201,6 +202,9 @@ static int bcma_host_pci_probe(struct pc bus->hosttype = BCMA_HOSTTYPE_PCI; bus->ops = &bcma_host_pci_ops; @@ -1739,7 +2205,7 @@ /* Register */ err = bcma_bus_register(bus); if (err) -@@ -222,7 +225,7 @@ err_kfree_bus: +@@ -222,7 +226,7 @@ err_kfree_bus: return err; } @@ -1748,7 +2214,7 @@ { struct bcma_bus *bus = pci_get_drvdata(dev); -@@ -265,6 +268,7 @@ static SIMPLE_DEV_PM_OPS(bcma_pm_ops, bc +@@ -265,9 +269,12 @@ static SIMPLE_DEV_PM_OPS(bcma_pm_ops, bc static DEFINE_PCI_DEVICE_TABLE(bcma_pci_bridge_tbl) = { { PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, 0x0576) }, @@ -1756,7 +2222,12 @@ { PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, 0x4331) }, { PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, 0x4353) }, { PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, 0x4357) }, -@@ -277,7 +281,7 @@ static struct pci_driver bcma_pci_bridge ++ { PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, 0x4358) }, ++ { PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, 0x4359) }, + { PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, 0x4727) }, + { 0, }, + }; +@@ -277,7 +284,7 @@ static struct pci_driver bcma_pci_bridge .name = "bcma-pci-bridge", .id_table = bcma_pci_bridge_tbl, .probe = bcma_host_pci_probe, @@ -1765,9 +2236,27 @@ .driver.pm = BCMA_PM_OPS, }; +--- a/drivers/bcma/host_soc.c ++++ b/drivers/bcma/host_soc.c +@@ -143,7 +143,7 @@ static void bcma_host_soc_awrite32(struc + writel(value, core->io_wrap + offset); + } + +-const struct bcma_host_ops bcma_host_soc_ops = { ++static const struct bcma_host_ops bcma_host_soc_ops = { + .read8 = bcma_host_soc_read8, + .read16 = bcma_host_soc_read16, + .read32 = bcma_host_soc_read32, --- a/drivers/bcma/main.c +++ b/drivers/bcma/main.c -@@ -13,6 +13,12 @@ +@@ -7,12 +7,19 @@ + + #include "bcma_private.h" + #include <linux/module.h> ++#include <linux/platform_device.h> + #include <linux/bcma/bcma.h> + #include <linux/slab.h> + MODULE_DESCRIPTION("Broadcom's specific AMBA driver"); MODULE_LICENSE("GPL"); @@ -1780,7 +2269,7 @@ static int bcma_bus_match(struct device *dev, struct device_driver *drv); static int bcma_device_probe(struct device *dev); static int bcma_device_remove(struct device *dev); -@@ -55,7 +61,14 @@ static struct bus_type bcma_bus_type = { +@@ -55,7 +62,14 @@ static struct bus_type bcma_bus_type = { .dev_attrs = bcma_device_attrs, }; @@ -1796,15 +2285,27 @@ { struct bcma_device *core; -@@ -65,6 +78,7 @@ static struct bcma_device *bcma_find_cor +@@ -65,6 +79,19 @@ static struct bcma_device *bcma_find_cor } return NULL; } +EXPORT_SYMBOL_GPL(bcma_find_core); ++ ++static struct bcma_device *bcma_find_core_unit(struct bcma_bus *bus, u16 coreid, ++ u8 unit) ++{ ++ struct bcma_device *core; ++ ++ list_for_each_entry(core, &bus->cores, list) { ++ if (core->id.id == coreid && core->core_unit == unit) ++ return core; ++ } ++ return NULL; ++} static void bcma_release_core_dev(struct device *dev) { -@@ -84,16 +98,18 @@ static int bcma_register_cores(struct bc +@@ -84,16 +111,18 @@ static int bcma_register_cores(struct bc list_for_each_entry(core, &bus->cores, list) { /* We support that cores ourself */ switch (core->id.id) { @@ -1824,7 +2325,7 @@ switch (bus->hosttype) { case BCMA_HOSTTYPE_PCI: -@@ -111,8 +127,9 @@ static int bcma_register_cores(struct bc +@@ -111,41 +140,77 @@ static int bcma_register_cores(struct bc err = device_register(&core->dev); if (err) { @@ -1836,7 +2337,38 @@ continue; } core->dev_registered = true; -@@ -132,20 +149,24 @@ static void bcma_unregister_cores(struct + dev_id++; + } + ++#ifdef CONFIG_BCMA_SFLASH ++ if (bus->drv_cc.sflash.present) { ++ err = platform_device_register(&bcma_sflash_dev); ++ if (err) ++ bcma_err(bus, "Error registering serial flash\n"); ++ } ++#endif ++ ++#ifdef CONFIG_BCMA_NFLASH ++ if (bus->drv_cc.nflash.present) { ++ err = platform_device_register(&bcma_nflash_dev); ++ if (err) ++ bcma_err(bus, "Error registering NAND flash\n"); ++ } ++#endif ++ + return 0; + } + + static void bcma_unregister_cores(struct bcma_bus *bus) + { +- struct bcma_device *core; ++ struct bcma_device *core, *tmp; + +- list_for_each_entry(core, &bus->cores, list) { ++ list_for_each_entry_safe(core, tmp, &bus->cores, list) { ++ list_del(&core->list); + if (core->dev_registered) + device_unregister(&core->dev); } } @@ -1858,31 +2390,58 @@ return -1; } ++ /* Early init CC core */ ++ core = bcma_find_core(bus, bcma_cc_core_id(bus)); ++ if (core) { ++ bus->drv_cc.core = core; ++ bcma_core_chipcommon_early_init(&bus->drv_cc); ++ } ++ ++ /* Try to get SPROM */ ++ err = bcma_sprom_get(bus); ++ if (err == -ENOENT) { ++ bcma_err(bus, "No SPROM available\n"); ++ } else if (err) ++ bcma_err(bus, "Failed to get SPROM: %d\n", err); ++ /* Init CC core */ - core = bcma_find_core(bus, BCMA_CORE_CHIPCOMMON); + core = bcma_find_core(bus, bcma_cc_core_id(bus)); if (core) { bus->drv_cc.core = core; bcma_core_chipcommon_init(&bus->drv_cc); -@@ -165,17 +186,24 @@ int bcma_bus_register(struct bcma_bus *b - bcma_core_pci_init(&bus->drv_pci); +@@ -159,30 +224,47 @@ int bcma_bus_register(struct bcma_bus *b } + /* Init PCIE core */ +- core = bcma_find_core(bus, BCMA_CORE_PCIE); ++ core = bcma_find_core_unit(bus, BCMA_CORE_PCIE, 0); + if (core) { +- bus->drv_pci.core = core; +- bcma_core_pci_init(&bus->drv_pci); ++ bus->drv_pci[0].core = core; ++ bcma_core_pci_init(&bus->drv_pci[0]); + } + +- /* Try to get SPROM */ +- err = bcma_sprom_get(bus); +- if (err == -ENOENT) { +- pr_err("No SPROM available\n"); +- } else if (err) +- pr_err("Failed to get SPROM: %d\n", err); ++ /* Init PCIE core */ ++ core = bcma_find_core_unit(bus, BCMA_CORE_PCIE, 1); ++ if (core) { ++ bus->drv_pci[1].core = core; ++ bcma_core_pci_init(&bus->drv_pci[1]); ++ } ++ + /* Init GBIT MAC COMMON core */ + core = bcma_find_core(bus, BCMA_CORE_4706_MAC_GBIT_COMMON); + if (core) { + bus->drv_gmac_cmn.core = core; + bcma_core_gmac_cmn_init(&bus->drv_gmac_cmn); + } -+ - /* Try to get SPROM */ - err = bcma_sprom_get(bus); - if (err == -ENOENT) { -- pr_err("No SPROM available\n"); -+ bcma_err(bus, "No SPROM available\n"); - } else if (err) -- pr_err("Failed to get SPROM: %d\n", err); -+ bcma_err(bus, "Failed to get SPROM: %d\n", err); /* Register found cores */ bcma_register_cores(bus); @@ -1892,7 +2451,24 @@ return 0; } -@@ -196,14 +224,14 @@ int __init bcma_bus_early_register(struc + + void bcma_bus_unregister(struct bcma_bus *bus) + { ++ struct bcma_device *cores[3]; ++ ++ cores[0] = bcma_find_core(bus, BCMA_CORE_MIPS_74K); ++ cores[1] = bcma_find_core(bus, BCMA_CORE_PCIE); ++ cores[2] = bcma_find_core(bus, BCMA_CORE_4706_MAC_GBIT_COMMON); ++ + bcma_unregister_cores(bus); ++ ++ kfree(cores[2]); ++ kfree(cores[1]); ++ kfree(cores[0]); + } + + int __init bcma_bus_early_register(struct bcma_bus *bus, +@@ -196,14 +278,14 @@ int __init bcma_bus_early_register(struc bcma_init_bus(bus); match.manuf = BCMA_MANUF_BCM; @@ -1909,7 +2485,7 @@ return -1; } -@@ -215,12 +243,12 @@ int __init bcma_bus_early_register(struc +@@ -215,25 +297,25 @@ int __init bcma_bus_early_register(struc /* Scan for mips core */ err = bcma_bus_scan_early(bus, &match, core_mips); if (err) { @@ -1918,14 +2494,23 @@ return -1; } - /* Init CC core */ +- /* Init CC core */ - core = bcma_find_core(bus, BCMA_CORE_CHIPCOMMON); ++ /* Early init CC core */ + core = bcma_find_core(bus, bcma_cc_core_id(bus)); if (core) { bus->drv_cc.core = core; - bcma_core_chipcommon_init(&bus->drv_cc); -@@ -233,7 +261,7 @@ int __init bcma_bus_early_register(struc - bcma_core_mips_init(&bus->drv_mips); +- bcma_core_chipcommon_init(&bus->drv_cc); ++ bcma_core_chipcommon_early_init(&bus->drv_cc); + } + +- /* Init MIPS core */ ++ /* Early init MIPS core */ + core = bcma_find_core(bus, BCMA_CORE_MIPS_74K); + if (core) { + bus->drv_mips.core = core; +- bcma_core_mips_init(&bus->drv_mips); ++ bcma_core_mips_early_init(&bus->drv_mips); } - pr_info("Early bus registered\n"); @@ -1933,7 +2518,7 @@ return 0; } -@@ -259,8 +287,7 @@ int bcma_bus_resume(struct bcma_bus *bus +@@ -259,8 +341,7 @@ int bcma_bus_resume(struct bcma_bus *bus struct bcma_device *core; /* Init CC core */ @@ -2038,12 +2623,12 @@ + break; + default: + return "UNKNOWN"; -+ } + } + + for (i = 0; i < size; i++) { + if (names[i].id == id->id) + return names[i].name; - } ++ } + return "UNKNOWN"; } @@ -2144,15 +2729,28 @@ bus->init_done = true; } -@@ -392,6 +460,7 @@ int bcma_bus_scan(struct bcma_bus *bus) +@@ -392,9 +460,12 @@ int bcma_bus_scan(struct bcma_bus *bus) bcma_scan_switch_core(bus, erombase); while (eromptr < eromend) { + struct bcma_device *other_core; struct bcma_device *core = kzalloc(sizeof(*core), GFP_KERNEL); - if (!core) - return -ENOMEM; -@@ -414,14 +483,15 @@ int bcma_bus_scan(struct bcma_bus *bus) +- if (!core) +- return -ENOMEM; ++ if (!core) { ++ err = -ENOMEM; ++ goto out; ++ } + INIT_LIST_HEAD(&core->list); + core->bus = bus; + +@@ -409,25 +480,28 @@ int bcma_bus_scan(struct bcma_bus *bus) + } else if (err == -ESPIPE) { + break; + } +- return err; ++ goto out; + } core->core_index = core_num++; bus->nr_cores++; @@ -2173,8 +2771,22 @@ + list_add_tail(&core->list, &bus->cores); } ++ err = 0; ++out: if (bus->hosttype == BCMA_HOSTTYPE_SOC) -@@ -471,13 +541,12 @@ int __init bcma_bus_scan_early(struct bc + iounmap(eromptr); + +- return 0; ++ return err; + } + + int __init bcma_bus_scan_early(struct bcma_bus *bus, +@@ -467,21 +541,21 @@ int __init bcma_bus_scan_early(struct bc + else if (err == -ESPIPE) + break; + else if (err < 0) +- return err; ++ goto out; core->core_index = core_num++; bus->nr_cores++; @@ -2193,6 +2805,11 @@ err = 0; break; } + ++out: + if (bus->hosttype == BCMA_HOSTTYPE_SOC) + iounmap(eromptr); + --- a/drivers/bcma/scan.h +++ b/drivers/bcma/scan.h @@ -27,7 +27,7 @@ @@ -2313,77 +2930,13 @@ bus->sprom.revision = sprom[SSB_SPROMSIZE_WORDS_R4 - 1] & SSB_SPROM_REVISION_REV; -@@ -137,102 +216,378 @@ static void bcma_sprom_extract_r8(struct +@@ -137,107 +216,390 @@ static void bcma_sprom_extract_r8(struct *(((__be16 *)bus->sprom.il0mac) + i) = cpu_to_be16(v); } - bus->sprom.board_rev = sprom[SPOFF(SSB_SPROM8_BOARDREV)]; + SPEX(board_rev, SSB_SPROM8_BOARDREV, ~0, 0); - -- bus->sprom.txpid2g[0] = (sprom[SPOFF(SSB_SPROM4_TXPID2G01)] & -- SSB_SPROM4_TXPID2G0) >> SSB_SPROM4_TXPID2G0_SHIFT; -- bus->sprom.txpid2g[1] = (sprom[SPOFF(SSB_SPROM4_TXPID2G01)] & -- SSB_SPROM4_TXPID2G1) >> SSB_SPROM4_TXPID2G1_SHIFT; -- bus->sprom.txpid2g[2] = (sprom[SPOFF(SSB_SPROM4_TXPID2G23)] & -- SSB_SPROM4_TXPID2G2) >> SSB_SPROM4_TXPID2G2_SHIFT; -- bus->sprom.txpid2g[3] = (sprom[SPOFF(SSB_SPROM4_TXPID2G23)] & -- SSB_SPROM4_TXPID2G3) >> SSB_SPROM4_TXPID2G3_SHIFT; -- -- bus->sprom.txpid5gl[0] = (sprom[SPOFF(SSB_SPROM4_TXPID5GL01)] & -- SSB_SPROM4_TXPID5GL0) >> SSB_SPROM4_TXPID5GL0_SHIFT; -- bus->sprom.txpid5gl[1] = (sprom[SPOFF(SSB_SPROM4_TXPID5GL01)] & -- SSB_SPROM4_TXPID5GL1) >> SSB_SPROM4_TXPID5GL1_SHIFT; -- bus->sprom.txpid5gl[2] = (sprom[SPOFF(SSB_SPROM4_TXPID5GL23)] & -- SSB_SPROM4_TXPID5GL2) >> SSB_SPROM4_TXPID5GL2_SHIFT; -- bus->sprom.txpid5gl[3] = (sprom[SPOFF(SSB_SPROM4_TXPID5GL23)] & -- SSB_SPROM4_TXPID5GL3) >> SSB_SPROM4_TXPID5GL3_SHIFT; -- -- bus->sprom.txpid5g[0] = (sprom[SPOFF(SSB_SPROM4_TXPID5G01)] & -- SSB_SPROM4_TXPID5G0) >> SSB_SPROM4_TXPID5G0_SHIFT; -- bus->sprom.txpid5g[1] = (sprom[SPOFF(SSB_SPROM4_TXPID5G01)] & -- SSB_SPROM4_TXPID5G1) >> SSB_SPROM4_TXPID5G1_SHIFT; -- bus->sprom.txpid5g[2] = (sprom[SPOFF(SSB_SPROM4_TXPID5G23)] & -- SSB_SPROM4_TXPID5G2) >> SSB_SPROM4_TXPID5G2_SHIFT; -- bus->sprom.txpid5g[3] = (sprom[SPOFF(SSB_SPROM4_TXPID5G23)] & -- SSB_SPROM4_TXPID5G3) >> SSB_SPROM4_TXPID5G3_SHIFT; -- -- bus->sprom.txpid5gh[0] = (sprom[SPOFF(SSB_SPROM4_TXPID5GH01)] & -- SSB_SPROM4_TXPID5GH0) >> SSB_SPROM4_TXPID5GH0_SHIFT; -- bus->sprom.txpid5gh[1] = (sprom[SPOFF(SSB_SPROM4_TXPID5GH01)] & -- SSB_SPROM4_TXPID5GH1) >> SSB_SPROM4_TXPID5GH1_SHIFT; -- bus->sprom.txpid5gh[2] = (sprom[SPOFF(SSB_SPROM4_TXPID5GH23)] & -- SSB_SPROM4_TXPID5GH2) >> SSB_SPROM4_TXPID5GH2_SHIFT; -- bus->sprom.txpid5gh[3] = (sprom[SPOFF(SSB_SPROM4_TXPID5GH23)] & -- SSB_SPROM4_TXPID5GH3) >> SSB_SPROM4_TXPID5GH3_SHIFT; -- -- bus->sprom.boardflags_lo = sprom[SPOFF(SSB_SPROM8_BFLLO)]; -- bus->sprom.boardflags_hi = sprom[SPOFF(SSB_SPROM8_BFLHI)]; -- bus->sprom.boardflags2_lo = sprom[SPOFF(SSB_SPROM8_BFL2LO)]; -- bus->sprom.boardflags2_hi = sprom[SPOFF(SSB_SPROM8_BFL2HI)]; -- -- bus->sprom.country_code = sprom[SPOFF(SSB_SPROM8_CCODE)]; -- -- bus->sprom.fem.ghz2.tssipos = (sprom[SPOFF(SSB_SPROM8_FEM2G)] & -- SSB_SROM8_FEM_TSSIPOS) >> SSB_SROM8_FEM_TSSIPOS_SHIFT; -- bus->sprom.fem.ghz2.extpa_gain = (sprom[SPOFF(SSB_SPROM8_FEM2G)] & -- SSB_SROM8_FEM_EXTPA_GAIN) >> SSB_SROM8_FEM_EXTPA_GAIN_SHIFT; -- bus->sprom.fem.ghz2.pdet_range = (sprom[SPOFF(SSB_SPROM8_FEM2G)] & -- SSB_SROM8_FEM_PDET_RANGE) >> SSB_SROM8_FEM_PDET_RANGE_SHIFT; -- bus->sprom.fem.ghz2.tr_iso = (sprom[SPOFF(SSB_SPROM8_FEM2G)] & -- SSB_SROM8_FEM_TR_ISO) >> SSB_SROM8_FEM_TR_ISO_SHIFT; -- bus->sprom.fem.ghz2.antswlut = (sprom[SPOFF(SSB_SPROM8_FEM2G)] & -- SSB_SROM8_FEM_ANTSWLUT) >> SSB_SROM8_FEM_ANTSWLUT_SHIFT; -- -- bus->sprom.fem.ghz5.tssipos = (sprom[SPOFF(SSB_SPROM8_FEM5G)] & -- SSB_SROM8_FEM_TSSIPOS) >> SSB_SROM8_FEM_TSSIPOS_SHIFT; -- bus->sprom.fem.ghz5.extpa_gain = (sprom[SPOFF(SSB_SPROM8_FEM5G)] & -- SSB_SROM8_FEM_EXTPA_GAIN) >> SSB_SROM8_FEM_EXTPA_GAIN_SHIFT; -- bus->sprom.fem.ghz5.pdet_range = (sprom[SPOFF(SSB_SPROM8_FEM5G)] & -- SSB_SROM8_FEM_PDET_RANGE) >> SSB_SROM8_FEM_PDET_RANGE_SHIFT; -- bus->sprom.fem.ghz5.tr_iso = (sprom[SPOFF(SSB_SPROM8_FEM5G)] & -- SSB_SROM8_FEM_TR_ISO) >> SSB_SROM8_FEM_TR_ISO_SHIFT; -- bus->sprom.fem.ghz5.antswlut = (sprom[SPOFF(SSB_SPROM8_FEM5G)] & -- SSB_SROM8_FEM_ANTSWLUT) >> SSB_SROM8_FEM_ANTSWLUT_SHIFT; ++ + SPEX(txpid2g[0], SSB_SPROM4_TXPID2G01, SSB_SPROM4_TXPID2G0, + SSB_SPROM4_TXPID2G0_SHIFT); + SPEX(txpid2g[1], SSB_SPROM4_TXPID2G01, SSB_SPROM4_TXPID2G1, @@ -2459,7 +3012,71 @@ + SPEX(core_pwr_info[i].pa_5gh[1], o + SSB_SROM8_5GH_PA_1, ~0, 0); + SPEX(core_pwr_info[i].pa_5gh[2], o + SSB_SROM8_5GH_PA_2, ~0, 0); + } -+ + +- bus->sprom.txpid2g[0] = (sprom[SPOFF(SSB_SPROM4_TXPID2G01)] & +- SSB_SPROM4_TXPID2G0) >> SSB_SPROM4_TXPID2G0_SHIFT; +- bus->sprom.txpid2g[1] = (sprom[SPOFF(SSB_SPROM4_TXPID2G01)] & +- SSB_SPROM4_TXPID2G1) >> SSB_SPROM4_TXPID2G1_SHIFT; +- bus->sprom.txpid2g[2] = (sprom[SPOFF(SSB_SPROM4_TXPID2G23)] & +- SSB_SPROM4_TXPID2G2) >> SSB_SPROM4_TXPID2G2_SHIFT; +- bus->sprom.txpid2g[3] = (sprom[SPOFF(SSB_SPROM4_TXPID2G23)] & +- SSB_SPROM4_TXPID2G3) >> SSB_SPROM4_TXPID2G3_SHIFT; +- +- bus->sprom.txpid5gl[0] = (sprom[SPOFF(SSB_SPROM4_TXPID5GL01)] & +- SSB_SPROM4_TXPID5GL0) >> SSB_SPROM4_TXPID5GL0_SHIFT; +- bus->sprom.txpid5gl[1] = (sprom[SPOFF(SSB_SPROM4_TXPID5GL01)] & +- SSB_SPROM4_TXPID5GL1) >> SSB_SPROM4_TXPID5GL1_SHIFT; +- bus->sprom.txpid5gl[2] = (sprom[SPOFF(SSB_SPROM4_TXPID5GL23)] & +- SSB_SPROM4_TXPID5GL2) >> SSB_SPROM4_TXPID5GL2_SHIFT; +- bus->sprom.txpid5gl[3] = (sprom[SPOFF(SSB_SPROM4_TXPID5GL23)] & +- SSB_SPROM4_TXPID5GL3) >> SSB_SPROM4_TXPID5GL3_SHIFT; +- +- bus->sprom.txpid5g[0] = (sprom[SPOFF(SSB_SPROM4_TXPID5G01)] & +- SSB_SPROM4_TXPID5G0) >> SSB_SPROM4_TXPID5G0_SHIFT; +- bus->sprom.txpid5g[1] = (sprom[SPOFF(SSB_SPROM4_TXPID5G01)] & +- SSB_SPROM4_TXPID5G1) >> SSB_SPROM4_TXPID5G1_SHIFT; +- bus->sprom.txpid5g[2] = (sprom[SPOFF(SSB_SPROM4_TXPID5G23)] & +- SSB_SPROM4_TXPID5G2) >> SSB_SPROM4_TXPID5G2_SHIFT; +- bus->sprom.txpid5g[3] = (sprom[SPOFF(SSB_SPROM4_TXPID5G23)] & +- SSB_SPROM4_TXPID5G3) >> SSB_SPROM4_TXPID5G3_SHIFT; +- +- bus->sprom.txpid5gh[0] = (sprom[SPOFF(SSB_SPROM4_TXPID5GH01)] & +- SSB_SPROM4_TXPID5GH0) >> SSB_SPROM4_TXPID5GH0_SHIFT; +- bus->sprom.txpid5gh[1] = (sprom[SPOFF(SSB_SPROM4_TXPID5GH01)] & +- SSB_SPROM4_TXPID5GH1) >> SSB_SPROM4_TXPID5GH1_SHIFT; +- bus->sprom.txpid5gh[2] = (sprom[SPOFF(SSB_SPROM4_TXPID5GH23)] & +- SSB_SPROM4_TXPID5GH2) >> SSB_SPROM4_TXPID5GH2_SHIFT; +- bus->sprom.txpid5gh[3] = (sprom[SPOFF(SSB_SPROM4_TXPID5GH23)] & +- SSB_SPROM4_TXPID5GH3) >> SSB_SPROM4_TXPID5GH3_SHIFT; +- +- bus->sprom.boardflags_lo = sprom[SPOFF(SSB_SPROM8_BFLLO)]; +- bus->sprom.boardflags_hi = sprom[SPOFF(SSB_SPROM8_BFLHI)]; +- bus->sprom.boardflags2_lo = sprom[SPOFF(SSB_SPROM8_BFL2LO)]; +- bus->sprom.boardflags2_hi = sprom[SPOFF(SSB_SPROM8_BFL2HI)]; +- +- bus->sprom.country_code = sprom[SPOFF(SSB_SPROM8_CCODE)]; +- +- bus->sprom.fem.ghz2.tssipos = (sprom[SPOFF(SSB_SPROM8_FEM2G)] & +- SSB_SROM8_FEM_TSSIPOS) >> SSB_SROM8_FEM_TSSIPOS_SHIFT; +- bus->sprom.fem.ghz2.extpa_gain = (sprom[SPOFF(SSB_SPROM8_FEM2G)] & +- SSB_SROM8_FEM_EXTPA_GAIN) >> SSB_SROM8_FEM_EXTPA_GAIN_SHIFT; +- bus->sprom.fem.ghz2.pdet_range = (sprom[SPOFF(SSB_SPROM8_FEM2G)] & +- SSB_SROM8_FEM_PDET_RANGE) >> SSB_SROM8_FEM_PDET_RANGE_SHIFT; +- bus->sprom.fem.ghz2.tr_iso = (sprom[SPOFF(SSB_SPROM8_FEM2G)] & +- SSB_SROM8_FEM_TR_ISO) >> SSB_SROM8_FEM_TR_ISO_SHIFT; +- bus->sprom.fem.ghz2.antswlut = (sprom[SPOFF(SSB_SPROM8_FEM2G)] & +- SSB_SROM8_FEM_ANTSWLUT) >> SSB_SROM8_FEM_ANTSWLUT_SHIFT; +- +- bus->sprom.fem.ghz5.tssipos = (sprom[SPOFF(SSB_SPROM8_FEM5G)] & +- SSB_SROM8_FEM_TSSIPOS) >> SSB_SROM8_FEM_TSSIPOS_SHIFT; +- bus->sprom.fem.ghz5.extpa_gain = (sprom[SPOFF(SSB_SPROM8_FEM5G)] & +- SSB_SROM8_FEM_EXTPA_GAIN) >> SSB_SROM8_FEM_EXTPA_GAIN_SHIFT; +- bus->sprom.fem.ghz5.pdet_range = (sprom[SPOFF(SSB_SPROM8_FEM5G)] & +- SSB_SROM8_FEM_PDET_RANGE) >> SSB_SROM8_FEM_PDET_RANGE_SHIFT; +- bus->sprom.fem.ghz5.tr_iso = (sprom[SPOFF(SSB_SPROM8_FEM5G)] & +- SSB_SROM8_FEM_TR_ISO) >> SSB_SROM8_FEM_TR_ISO_SHIFT; +- bus->sprom.fem.ghz5.antswlut = (sprom[SPOFF(SSB_SPROM8_FEM5G)] & +- SSB_SROM8_FEM_ANTSWLUT) >> SSB_SROM8_FEM_ANTSWLUT_SHIFT; + SPEX(fem.ghz2.tssipos, SSB_SPROM8_FEM2G, SSB_SROM8_FEM_TSSIPOS, + SSB_SROM8_FEM_TSSIPOS_SHIFT); + SPEX(fem.ghz2.extpa_gain, SSB_SPROM8_FEM2G, SSB_SROM8_FEM_EXTPA_GAIN, @@ -2673,7 +3290,11 @@ + /* for these chips OTP is always available */ + present = true; + break; -+ ++ case BCMA_CHIP_ID_BCM43227: ++ case BCMA_CHIP_ID_BCM43228: ++ case BCMA_CHIP_ID_BCM43428: ++ present = chip_status & BCMA_CC_CHIPST_43228_OTP_PRESENT; ++ break; + default: + present = false; + break; @@ -2767,16 +3388,29 @@ bcma_chipco_bcm4331_ext_pa_lines_ctl(&bus->drv_cc, true); err = bcma_sprom_valid(sprom); +- if (err) ++ if (err) { ++ bcma_warn(bus, "invalid sprom read from the PCIe card, try to use fallback sprom\n"); ++ err = bcma_fill_sprom_with_fallback(bus, &bus->sprom); + goto out; ++ } + + bcma_sprom_extract_r8(bus, sprom); + --- a/include/linux/bcma/bcma.h +++ b/include/linux/bcma/bcma.h -@@ -7,6 +7,7 @@ +@@ -7,9 +7,10 @@ #include <linux/bcma/bcma_driver_chipcommon.h> #include <linux/bcma/bcma_driver_pci.h> #include <linux/bcma/bcma_driver_mips.h> +#include <linux/bcma/bcma_driver_gmac_cmn.h> #include <linux/ssb/ssb.h> /* SPROM sharing */ - #include "bcma_regs.h" +-#include "bcma_regs.h" ++#include <linux/bcma/bcma_regs.h> + + struct bcma_device; + struct bcma_bus; @@ -26,6 +27,11 @@ struct bcma_chipinfo { u8 pkg; }; @@ -2877,7 +3511,8 @@ + u8 num; struct bcma_drv_cc drv_cc; - struct bcma_drv_pci drv_pci; +- struct bcma_drv_pci drv_pci; ++ struct bcma_drv_pci drv_pci[2]; struct bcma_drv_mips drv_mips; + struct bcma_drv_gmac_cmn drv_gmac_cmn; @@ -2893,7 +3528,24 @@ extern int bcma_core_enable(struct bcma_device *core, u32 flags); --- a/include/linux/bcma/bcma_driver_chipcommon.h +++ b/include/linux/bcma/bcma_driver_chipcommon.h -@@ -56,6 +56,9 @@ +@@ -24,7 +24,7 @@ + #define BCMA_CC_FLASHT_NONE 0x00000000 /* No flash */ + #define BCMA_CC_FLASHT_STSER 0x00000100 /* ST serial flash */ + #define BCMA_CC_FLASHT_ATSER 0x00000200 /* Atmel serial flash */ +-#define BCMA_CC_FLASHT_NFLASH 0x00000200 ++#define BCMA_CC_FLASHT_NFLASH 0x00000200 /* NAND flash */ + #define BCMA_CC_FLASHT_PARA 0x00000700 /* Parallel flash */ + #define BCMA_CC_CAP_PLLT 0x00038000 /* PLL Type */ + #define BCMA_PLLTYPE_NONE 0x00000000 +@@ -45,6 +45,7 @@ + #define BCMA_CC_CAP_PMU 0x10000000 /* PMU available (rev >= 20) */ + #define BCMA_CC_CAP_ECI 0x20000000 /* ECI available (rev >= 20) */ + #define BCMA_CC_CAP_SPROM 0x40000000 /* SPROM present */ ++#define BCMA_CC_CAP_NFLASH 0x80000000 /* NAND flash present (rev >= 35 or BCM4706?) */ + #define BCMA_CC_CORECTL 0x0008 + #define BCMA_CC_CORECTL_UARTCLK0 0x00000001 /* Drive UART with internal clock */ + #define BCMA_CC_CORECTL_SE 0x00000002 /* sync clk out enable (corerev >= 3) */ +@@ -56,6 +57,9 @@ #define BCMA_CC_OTPS_HW_PROTECT 0x00000001 #define BCMA_CC_OTPS_SW_PROTECT 0x00000002 #define BCMA_CC_OTPS_CID_PROTECT 0x00000004 @@ -2903,7 +3555,7 @@ #define BCMA_CC_OTPC 0x0014 /* OTP control */ #define BCMA_CC_OTPC_RECWAIT 0xFF000000 #define BCMA_CC_OTPC_PROGWAIT 0x00FFFF00 -@@ -72,6 +75,8 @@ +@@ -72,6 +76,8 @@ #define BCMA_CC_OTPP_READ 0x40000000 #define BCMA_CC_OTPP_START 0x80000000 #define BCMA_CC_OTPP_BUSY 0x80000000 @@ -2912,7 +3564,7 @@ #define BCMA_CC_IRQSTAT 0x0020 #define BCMA_CC_IRQMASK 0x0024 #define BCMA_CC_IRQ_GPIO 0x00000001 /* gpio intr */ -@@ -79,6 +84,15 @@ +@@ -79,6 +85,22 @@ #define BCMA_CC_IRQ_WDRESET 0x80000000 /* watchdog reset occurred */ #define BCMA_CC_CHIPCTL 0x0028 /* Rev >= 11 only */ #define BCMA_CC_CHIPSTAT 0x002C /* Rev >= 11 only */ @@ -2920,15 +3572,81 @@ +#define BCMA_CC_CHIPST_4313_OTP_PRESENT 2 +#define BCMA_CC_CHIPST_4331_SPROM_PRESENT 2 +#define BCMA_CC_CHIPST_4331_OTP_PRESENT 4 ++#define BCMA_CC_CHIPST_43228_ILP_DIV_EN 0x00000001 ++#define BCMA_CC_CHIPST_43228_OTP_PRESENT 0x00000002 ++#define BCMA_CC_CHIPST_43228_SERDES_REFCLK_PADSEL 0x00000004 ++#define BCMA_CC_CHIPST_43228_SDIO_MODE 0x00000008 ++#define BCMA_CC_CHIPST_43228_SDIO_OTP_PRESENT 0x00000010 ++#define BCMA_CC_CHIPST_43228_SDIO_RESET 0x00000020 +#define BCMA_CC_CHIPST_4706_PKG_OPTION BIT(0) /* 0: full-featured package 1: low-cost package */ +#define BCMA_CC_CHIPST_4706_SFLASH_PRESENT BIT(1) /* 0: parallel, 1: serial flash is present */ +#define BCMA_CC_CHIPST_4706_SFLASH_TYPE BIT(2) /* 0: 8b-p/ST-s flash, 1: 16b-p/Atmal-s flash */ +#define BCMA_CC_CHIPST_4706_MIPS_BENDIAN BIT(3) /* 0: little, 1: big endian */ +#define BCMA_CC_CHIPST_4706_PCIE1_DISABLE BIT(5) /* PCIE1 enable strap pin */ ++#define BCMA_CC_CHIPST_5357_NAND_BOOT BIT(4) /* NAND boot, valid for CC rev 38 and/or BCM5357 */ #define BCMA_CC_JCMD 0x0030 /* Rev >= 10 only */ #define BCMA_CC_JCMD_START 0x80000000 #define BCMA_CC_JCMD_BUSY 0x80000000 -@@ -181,6 +195,22 @@ +@@ -108,10 +130,58 @@ + #define BCMA_CC_JCTL_EXT_EN 2 /* Enable external targets */ + #define BCMA_CC_JCTL_EN 1 /* Enable Jtag master */ + #define BCMA_CC_FLASHCTL 0x0040 ++/* Start/busy bit in flashcontrol */ ++#define BCMA_CC_FLASHCTL_OPCODE 0x000000ff ++#define BCMA_CC_FLASHCTL_ACTION 0x00000700 ++#define BCMA_CC_FLASHCTL_CS_ACTIVE 0x00001000 /* Chip Select Active, rev >= 20 */ + #define BCMA_CC_FLASHCTL_START 0x80000000 + #define BCMA_CC_FLASHCTL_BUSY BCMA_CC_FLASHCTL_START ++/* Flashcontrol action + opcodes for ST flashes */ ++#define BCMA_CC_FLASHCTL_ST_WREN 0x0006 /* Write Enable */ ++#define BCMA_CC_FLASHCTL_ST_WRDIS 0x0004 /* Write Disable */ ++#define BCMA_CC_FLASHCTL_ST_RDSR 0x0105 /* Read Status Register */ ++#define BCMA_CC_FLASHCTL_ST_WRSR 0x0101 /* Write Status Register */ ++#define BCMA_CC_FLASHCTL_ST_READ 0x0303 /* Read Data Bytes */ ++#define BCMA_CC_FLASHCTL_ST_PP 0x0302 /* Page Program */ ++#define BCMA_CC_FLASHCTL_ST_SE 0x02d8 /* Sector Erase */ ++#define BCMA_CC_FLASHCTL_ST_BE 0x00c7 /* Bulk Erase */ ++#define BCMA_CC_FLASHCTL_ST_DP 0x00b9 /* Deep Power-down */ ++#define BCMA_CC_FLASHCTL_ST_RES 0x03ab /* Read Electronic Signature */ ++#define BCMA_CC_FLASHCTL_ST_CSA 0x1000 /* Keep chip select asserted */ ++#define BCMA_CC_FLASHCTL_ST_SSE 0x0220 /* Sub-sector Erase */ ++/* Flashcontrol action + opcodes for Atmel flashes */ ++#define BCMA_CC_FLASHCTL_AT_READ 0x07e8 ++#define BCMA_CC_FLASHCTL_AT_PAGE_READ 0x07d2 ++#define BCMA_CC_FLASHCTL_AT_STATUS 0x01d7 ++#define BCMA_CC_FLASHCTL_AT_BUF1_WRITE 0x0384 ++#define BCMA_CC_FLASHCTL_AT_BUF2_WRITE 0x0387 ++#define BCMA_CC_FLASHCTL_AT_BUF1_ERASE_PROGRAM 0x0283 ++#define BCMA_CC_FLASHCTL_AT_BUF2_ERASE_PROGRAM 0x0286 ++#define BCMA_CC_FLASHCTL_AT_BUF1_PROGRAM 0x0288 ++#define BCMA_CC_FLASHCTL_AT_BUF2_PROGRAM 0x0289 ++#define BCMA_CC_FLASHCTL_AT_PAGE_ERASE 0x0281 ++#define BCMA_CC_FLASHCTL_AT_BLOCK_ERASE 0x0250 ++#define BCMA_CC_FLASHCTL_AT_BUF1_WRITE_ERASE_PROGRAM 0x0382 ++#define BCMA_CC_FLASHCTL_AT_BUF2_WRITE_ERASE_PROGRAM 0x0385 ++#define BCMA_CC_FLASHCTL_AT_BUF1_LOAD 0x0253 ++#define BCMA_CC_FLASHCTL_AT_BUF2_LOAD 0x0255 ++#define BCMA_CC_FLASHCTL_AT_BUF1_COMPARE 0x0260 ++#define BCMA_CC_FLASHCTL_AT_BUF2_COMPARE 0x0261 ++#define BCMA_CC_FLASHCTL_AT_BUF1_REPROGRAM 0x0258 ++#define BCMA_CC_FLASHCTL_AT_BUF2_REPROGRAM 0x0259 + #define BCMA_CC_FLASHADDR 0x0044 + #define BCMA_CC_FLASHDATA 0x0048 ++/* Status register bits for ST flashes */ ++#define BCMA_CC_FLASHDATA_ST_WIP 0x01 /* Write In Progress */ ++#define BCMA_CC_FLASHDATA_ST_WEL 0x02 /* Write Enable Latch */ ++#define BCMA_CC_FLASHDATA_ST_BP_MASK 0x1c /* Block Protect */ ++#define BCMA_CC_FLASHDATA_ST_BP_SHIFT 2 ++#define BCMA_CC_FLASHDATA_ST_SRWD 0x80 /* Status Register Write Disable */ ++/* Status register bits for Atmel flashes */ ++#define BCMA_CC_FLASHDATA_AT_READY 0x80 ++#define BCMA_CC_FLASHDATA_AT_MISMATCH 0x40 ++#define BCMA_CC_FLASHDATA_AT_ID_MASK 0x38 ++#define BCMA_CC_FLASHDATA_AT_ID_SHIFT 3 + #define BCMA_CC_BCAST_ADDR 0x0050 + #define BCMA_CC_BCAST_DATA 0x0054 + #define BCMA_CC_GPIOPULLUP 0x0058 /* Rev >= 20 only */ +@@ -181,6 +251,45 @@ #define BCMA_CC_FLASH_CFG 0x0128 #define BCMA_CC_FLASH_CFG_DS 0x0010 /* Data size, 0=8bit, 1=16bit */ #define BCMA_CC_FLASH_WAITCNT 0x012C @@ -2948,18 +3666,95 @@ +#define BCMA_CC_SROM_CONTROL_SIZE_16K 0x00000004 +#define BCMA_CC_SROM_CONTROL_SIZE_SHIFT 1 +#define BCMA_CC_SROM_CONTROL_PRESENT 0x00000001 ++/* Block 0x140 - 0x190 registers are chipset specific */ ++#define BCMA_CC_4706_FLASHSCFG 0x18C /* Flash struct configuration */ ++#define BCMA_CC_4706_FLASHSCFG_MASK 0x000000ff ++#define BCMA_CC_4706_FLASHSCFG_SF1 0x00000001 /* 2nd serial flash present */ ++#define BCMA_CC_4706_FLASHSCFG_PF1 0x00000002 /* 2nd parallel flash present */ ++#define BCMA_CC_4706_FLASHSCFG_SF1_TYPE 0x00000004 /* 2nd serial flash type : 0 : ST, 1 : Atmel */ ++#define BCMA_CC_4706_FLASHSCFG_NF1 0x00000008 /* 2nd NAND flash present */ ++#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_MASK 0x000000f0 ++#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_4MB 0x00000010 /* 4MB */ ++#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_8MB 0x00000020 /* 8MB */ ++#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_16MB 0x00000030 /* 16MB */ ++#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_32MB 0x00000040 /* 32MB */ ++#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_64MB 0x00000050 /* 64MB */ ++#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_128MB 0x00000060 /* 128MB */ ++#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_256MB 0x00000070 /* 256MB */ ++/* NAND flash registers for BCM4706 (corerev = 31) */ ++#define BCMA_CC_NFLASH_CTL 0x01A0 ++#define BCMA_CC_NFLASH_CTL_ERR 0x08000000 ++#define BCMA_CC_NFLASH_CONF 0x01A4 ++#define BCMA_CC_NFLASH_COL_ADDR 0x01A8 ++#define BCMA_CC_NFLASH_ROW_ADDR 0x01AC ++#define BCMA_CC_NFLASH_DATA 0x01B0 ++#define BCMA_CC_NFLASH_WAITCNT0 0x01B4 /* 0x1E0 is defined as shared BCMA_CLKCTLST */ #define BCMA_CC_HW_WORKAROUND 0x01E4 /* Hardware workaround (rev >= 20) */ #define BCMA_CC_UART0_DATA 0x0300 -@@ -240,7 +270,6 @@ +@@ -240,7 +349,60 @@ #define BCMA_CC_PLLCTL_ADDR 0x0660 #define BCMA_CC_PLLCTL_DATA 0x0664 #define BCMA_CC_SPROM 0x0800 /* SPROM beginning */ -#define BCMA_CC_SPROM_PCIE6 0x0830 /* SPROM beginning on PCIe rev >= 6 */ ++/* NAND flash MLC controller registers (corerev >= 38) */ ++#define BCMA_CC_NAND_REVISION 0x0C00 ++#define BCMA_CC_NAND_CMD_START 0x0C04 ++#define BCMA_CC_NAND_CMD_ADDR_X 0x0C08 ++#define BCMA_CC_NAND_CMD_ADDR 0x0C0C ++#define BCMA_CC_NAND_CMD_END_ADDR 0x0C10 ++#define BCMA_CC_NAND_CS_NAND_SELECT 0x0C14 ++#define BCMA_CC_NAND_CS_NAND_XOR 0x0C18 ++#define BCMA_CC_NAND_SPARE_RD0 0x0C20 ++#define BCMA_CC_NAND_SPARE_RD4 0x0C24 ++#define BCMA_CC_NAND_SPARE_RD8 0x0C28 ++#define BCMA_CC_NAND_SPARE_RD12 0x0C2C ++#define BCMA_CC_NAND_SPARE_WR0 0x0C30 ++#define BCMA_CC_NAND_SPARE_WR4 0x0C34 ++#define BCMA_CC_NAND_SPARE_WR8 0x0C38 ++#define BCMA_CC_NAND_SPARE_WR12 0x0C3C ++#define BCMA_CC_NAND_ACC_CONTROL 0x0C40 ++#define BCMA_CC_NAND_CONFIG 0x0C48 ++#define BCMA_CC_NAND_TIMING_1 0x0C50 ++#define BCMA_CC_NAND_TIMING_2 0x0C54 ++#define BCMA_CC_NAND_SEMAPHORE 0x0C58 ++#define BCMA_CC_NAND_DEVID 0x0C60 ++#define BCMA_CC_NAND_DEVID_X 0x0C64 ++#define BCMA_CC_NAND_BLOCK_LOCK_STATUS 0x0C68 ++#define BCMA_CC_NAND_INTFC_STATUS 0x0C6C ++#define BCMA_CC_NAND_ECC_CORR_ADDR_X 0x0C70 ++#define BCMA_CC_NAND_ECC_CORR_ADDR 0x0C74 ++#define BCMA_CC_NAND_ECC_UNC_ADDR_X 0x0C78 ++#define BCMA_CC_NAND_ECC_UNC_ADDR 0x0C7C ++#define BCMA_CC_NAND_READ_ERROR_COUNT 0x0C80 ++#define BCMA_CC_NAND_CORR_STAT_THRESHOLD 0x0C84 ++#define BCMA_CC_NAND_READ_ADDR_X 0x0C90 ++#define BCMA_CC_NAND_READ_ADDR 0x0C94 ++#define BCMA_CC_NAND_PAGE_PROGRAM_ADDR_X 0x0C98 ++#define BCMA_CC_NAND_PAGE_PROGRAM_ADDR 0x0C9C ++#define BCMA_CC_NAND_COPY_BACK_ADDR_X 0x0CA0 ++#define BCMA_CC_NAND_COPY_BACK_ADDR 0x0CA4 ++#define BCMA_CC_NAND_BLOCK_ERASE_ADDR_X 0x0CA8 ++#define BCMA_CC_NAND_BLOCK_ERASE_ADDR 0x0CAC ++#define BCMA_CC_NAND_INV_READ_ADDR_X 0x0CB0 ++#define BCMA_CC_NAND_INV_READ_ADDR 0x0CB4 ++#define BCMA_CC_NAND_BLK_WR_PROTECT 0x0CC0 ++#define BCMA_CC_NAND_ACC_CONTROL_CS1 0x0CD0 ++#define BCMA_CC_NAND_CONFIG_CS1 0x0CD4 ++#define BCMA_CC_NAND_TIMING_1_CS1 0x0CD8 ++#define BCMA_CC_NAND_TIMING_2_CS1 0x0CDC ++#define BCMA_CC_NAND_SPARE_RD16 0x0D30 ++#define BCMA_CC_NAND_SPARE_RD20 0x0D34 ++#define BCMA_CC_NAND_SPARE_RD24 0x0D38 ++#define BCMA_CC_NAND_SPARE_RD28 0x0D3C ++#define BCMA_CC_NAND_CACHE_ADDR 0x0D40 ++#define BCMA_CC_NAND_CACHE_DATA 0x0D44 ++#define BCMA_CC_NAND_CTRL_CONFIG 0x0D48 ++#define BCMA_CC_NAND_CTRL_STATUS 0x0D4C /* Divider allocation in 4716/47162/5356 */ #define BCMA_CC_PMU5_MAINPLL_CPU 1 -@@ -256,6 +285,15 @@ +@@ -256,6 +418,15 @@ /* 4706 PMU */ #define BCMA_CC_PMU4706_MAINPLL_PLL0 0 @@ -2975,7 +3770,7 @@ /* ALP clock on pre-PMU chips */ #define BCMA_CC_PMU_ALP_CLOCK 20000000 -@@ -284,6 +322,19 @@ +@@ -284,6 +455,19 @@ #define BCMA_CC_PPL_PCHI_OFF 5 #define BCMA_CC_PPL_PCHI_MASK 0x0000003f @@ -2995,7 +3790,7 @@ /* BCM4331 ChipControl numbers. */ #define BCMA_CHIPCTL_4331_BT_COEXIST BIT(0) /* 0 disable */ #define BCMA_CHIPCTL_4331_SECI BIT(1) /* 0 SECI is disabled (JATG functional) */ -@@ -297,9 +348,18 @@ +@@ -297,9 +481,25 @@ #define BCMA_CHIPCTL_4331_OVR_PIPEAUXPWRDOWN BIT(9) /* override core control on pipe_AuxPowerDown */ #define BCMA_CHIPCTL_4331_PCIE_AUXCLKEN BIT(10) /* pcie_auxclkenable */ #define BCMA_CHIPCTL_4331_PCIE_PIPE_PLLDOWN BIT(11) /* pcie_pipe_pllpowerdown */ @@ -3011,10 +3806,88 @@ +/* 4313 Chip specific ChipControl register bits */ +#define BCMA_CCTRL_4313_12MA_LED_DRIVE 0x00000007 /* 12 mA drive strengh for later 4313 */ + ++/* BCM5357 ChipControl register bits */ ++#define BCMA_CHIPCTL_5357_EXTPA BIT(14) ++#define BCMA_CHIPCTL_5357_ANT_MUX_2O3 BIT(15) ++#define BCMA_CHIPCTL_5357_NFLASH BIT(16) ++#define BCMA_CHIPCTL_5357_I2S_PINS_ENABLE BIT(18) ++#define BCMA_CHIPCTL_5357_I2CSPI_PINS_ENABLE BIT(19) ++ /* Data for the PMU, if available. * Check availability with ((struct bcma_chipcommon)->capabilities & BCMA_CC_CAP_PMU) */ -@@ -387,5 +447,6 @@ extern void bcma_chipco_chipctl_maskset( +@@ -310,11 +510,35 @@ struct bcma_chipcommon_pmu { + + #ifdef CONFIG_BCMA_DRIVER_MIPS + struct bcma_pflash { ++ bool present; + u8 buswidth; + u32 window; + u32 window_size; + }; + ++#ifdef CONFIG_BCMA_SFLASH ++struct bcma_sflash { ++ bool present; ++ u32 window; ++ u32 blocksize; ++ u16 numblocks; ++ u32 size; ++ ++ struct mtd_info *mtd; ++}; ++#endif ++ ++#ifdef CONFIG_BCMA_NFLASH ++struct mtd_info; ++ ++struct bcma_nflash { ++ bool present; ++ bool boot; /* This is the flash the SoC boots from */ ++ ++ struct mtd_info *mtd; ++}; ++#endif ++ + struct bcma_serial_port { + void *regs; + unsigned long clockspeed; +@@ -330,11 +554,18 @@ struct bcma_drv_cc { + u32 capabilities; + u32 capabilities_ext; + u8 setup_done:1; ++ u8 early_setup_done:1; + /* Fast Powerup Delay constant */ + u16 fast_pwrup_delay; + struct bcma_chipcommon_pmu pmu; + #ifdef CONFIG_BCMA_DRIVER_MIPS + struct bcma_pflash pflash; ++#ifdef CONFIG_BCMA_SFLASH ++ struct bcma_sflash sflash; ++#endif ++#ifdef CONFIG_BCMA_NFLASH ++ struct bcma_nflash nflash; ++#endif + + int nr_serial_ports; + struct bcma_serial_port serial_ports[4]; +@@ -355,6 +586,7 @@ struct bcma_drv_cc { + bcma_cc_write32(cc, offset, (bcma_cc_read32(cc, offset) & (mask)) | (set)) + + extern void bcma_core_chipcommon_init(struct bcma_drv_cc *cc); ++extern void bcma_core_chipcommon_early_init(struct bcma_drv_cc *cc); + + extern void bcma_chipco_suspend(struct bcma_drv_cc *cc); + extern void bcma_chipco_resume(struct bcma_drv_cc *cc); +@@ -378,6 +610,7 @@ u32 bcma_chipco_gpio_polarity(struct bcm + + /* PMU support */ + extern void bcma_pmu_init(struct bcma_drv_cc *cc); ++extern void bcma_pmu_early_init(struct bcma_drv_cc *cc); + + extern void bcma_chipco_pll_write(struct bcma_drv_cc *cc, u32 offset, + u32 value); +@@ -387,5 +620,6 @@ extern void bcma_chipco_chipctl_maskset( u32 offset, u32 mask, u32 set); extern void bcma_chipco_regctl_maskset(struct bcma_drv_cc *cc, u32 offset, u32 mask, u32 set); @@ -3124,6 +3997,25 @@ +#endif + +#endif /* LINUX_BCMA_DRIVER_GMAC_CMN_H_ */ +--- a/include/linux/bcma/bcma_driver_mips.h ++++ b/include/linux/bcma/bcma_driver_mips.h +@@ -35,13 +35,16 @@ struct bcma_device; + struct bcma_drv_mips { + struct bcma_device *core; + u8 setup_done:1; ++ u8 early_setup_done:1; + unsigned int assigned_irqs; + }; + + #ifdef CONFIG_BCMA_DRIVER_MIPS + extern void bcma_core_mips_init(struct bcma_drv_mips *mcore); ++extern void bcma_core_mips_early_init(struct bcma_drv_mips *mcore); + #else + static inline void bcma_core_mips_init(struct bcma_drv_mips *mcore) { } ++static inline void bcma_core_mips_early_init(struct bcma_drv_mips *mcore) { } + #endif + + extern u32 bcma_cpu_clock(struct bcma_drv_mips *mcore); --- a/include/linux/bcma/bcma_driver_pci.h +++ b/include/linux/bcma/bcma_driver_pci.h @@ -53,11 +53,47 @@ struct pci_dev; @@ -3296,7 +4188,21 @@ #endif /* LINUX_BCMA_DRIVER_PCI_H_ */ --- a/include/linux/bcma/bcma_regs.h +++ b/include/linux/bcma/bcma_regs.h -@@ -56,4 +56,31 @@ +@@ -11,11 +11,13 @@ + #define BCMA_CLKCTLST_HAVEHTREQ 0x00000010 /* HT available request */ + #define BCMA_CLKCTLST_HWCROFF 0x00000020 /* Force HW clock request off */ + #define BCMA_CLKCTLST_EXTRESREQ 0x00000700 /* Mask of external resource requests */ ++#define BCMA_CLKCTLST_EXTRESREQ_SHIFT 8 + #define BCMA_CLKCTLST_HAVEALP 0x00010000 /* ALP available */ + #define BCMA_CLKCTLST_HAVEHT 0x00020000 /* HT available */ + #define BCMA_CLKCTLST_BP_ON_ALP 0x00040000 /* RO: running on ALP clock */ + #define BCMA_CLKCTLST_BP_ON_HT 0x00080000 /* RO: running on HT clock */ + #define BCMA_CLKCTLST_EXTRESST 0x07000000 /* Mask of external resource status */ ++#define BCMA_CLKCTLST_EXTRESST_SHIFT 24 + /* Is there any BCM4328 on BCMA bus? */ + #define BCMA_CLKCTLST_4328A0_HAVEHT 0x00010000 /* 4328a0 has reversed bits */ + #define BCMA_CLKCTLST_4328A0_HAVEALP 0x00020000 /* 4328a0 has reversed bits */ +@@ -56,4 +58,36 @@ #define BCMA_PCI_GPIO_XTAL 0x40 /* PCI config space GPIO 14 for Xtal powerup */ #define BCMA_PCI_GPIO_PLL 0x80 /* PCI config space GPIO 15 for PLL powerdown */ @@ -3327,4 +4233,9 @@ + * (2 ZettaBytes), high 32 bits + */ + ++#define BCMA_SOC_FLASH1 0x1fc00000 /* MIPS Flash Region 1 */ ++#define BCMA_SOC_FLASH1_SZ 0x00400000 /* MIPS Size of Flash Region 1 */ ++#define BCMA_SOC_FLASH2 0x1c000000 /* Flash Region 2 (region 1 shadowed here) */ ++#define BCMA_SOC_FLASH2_SZ 0x02000000 /* Size of Flash Region 2 */ ++ #endif /* LINUX_BCMA_REGS_H_ */ diff --git a/target/linux/generic/patches-3.3/026-bcma_pmu_regression.patch b/target/linux/generic/patches-3.3/026-bcma_pmu_regression.patch deleted file mode 100644 index 35ca6b81e..000000000 --- a/target/linux/generic/patches-3.3/026-bcma_pmu_regression.patch +++ /dev/null @@ -1,29 +0,0 @@ ---- a/drivers/bcma/driver_chipcommon_pmu.c -+++ b/drivers/bcma/driver_chipcommon_pmu.c -@@ -110,7 +110,7 @@ void bcma_pmu_workarounds(struct bcma_dr - /* enable 12 mA drive strenth for 4313 and set chipControl - register bit 1 */ - bcma_chipco_chipctl_maskset(cc, 0, -- BCMA_CCTRL_4313_12MA_LED_DRIVE, -+ ~BCMA_CCTRL_4313_12MA_LED_DRIVE, - BCMA_CCTRL_4313_12MA_LED_DRIVE); - break; - case BCMA_CHIP_ID_BCM4331: -@@ -124,14 +124,14 @@ void bcma_pmu_workarounds(struct bcma_dr - register bit 15 */ - if (bus->chipinfo.rev == 0) { - bcma_cc_maskset32(cc, BCMA_CC_CHIPCTL, -- BCMA_CCTRL_43224_GPIO_TOGGLE, -+ ~BCMA_CCTRL_43224_GPIO_TOGGLE, - BCMA_CCTRL_43224_GPIO_TOGGLE); - bcma_chipco_chipctl_maskset(cc, 0, -- BCMA_CCTRL_43224A0_12MA_LED_DRIVE, -+ ~BCMA_CCTRL_43224A0_12MA_LED_DRIVE, - BCMA_CCTRL_43224A0_12MA_LED_DRIVE); - } else { - bcma_chipco_chipctl_maskset(cc, 0, -- BCMA_CCTRL_43224B0_12MA_LED_DRIVE, -+ ~BCMA_CCTRL_43224B0_12MA_LED_DRIVE, - BCMA_CCTRL_43224B0_12MA_LED_DRIVE); - } - break; diff --git a/target/linux/generic/patches-3.3/027-bcma-add-missing-iounmap-on-error-path.patch b/target/linux/generic/patches-3.3/027-bcma-add-missing-iounmap-on-error-path.patch deleted file mode 100644 index dc8367b6c..000000000 --- a/target/linux/generic/patches-3.3/027-bcma-add-missing-iounmap-on-error-path.patch +++ /dev/null @@ -1,55 +0,0 @@ ---- a/drivers/bcma/scan.c -+++ b/drivers/bcma/scan.c -@@ -462,8 +462,10 @@ int bcma_bus_scan(struct bcma_bus *bus) - while (eromptr < eromend) { - struct bcma_device *other_core; - struct bcma_device *core = kzalloc(sizeof(*core), GFP_KERNEL); -- if (!core) -- return -ENOMEM; -+ if (!core) { -+ err = -ENOMEM; -+ goto out; -+ } - INIT_LIST_HEAD(&core->list); - core->bus = bus; - -@@ -478,7 +480,7 @@ int bcma_bus_scan(struct bcma_bus *bus) - } else if (err == -ESPIPE) { - break; - } -- return err; -+ goto out; - } - - core->core_index = core_num++; -@@ -494,10 +496,12 @@ int bcma_bus_scan(struct bcma_bus *bus) - list_add_tail(&core->list, &bus->cores); - } - -+ err = 0; -+out: - if (bus->hosttype == BCMA_HOSTTYPE_SOC) - iounmap(eromptr); - -- return 0; -+ return err; - } - - int __init bcma_bus_scan_early(struct bcma_bus *bus, -@@ -537,7 +541,7 @@ int __init bcma_bus_scan_early(struct bc - else if (err == -ESPIPE) - break; - else if (err < 0) -- return err; -+ goto out; - - core->core_index = core_num++; - bus->nr_cores++; -@@ -551,6 +555,7 @@ int __init bcma_bus_scan_early(struct bc - break; - } - -+out: - if (bus->hosttype == BCMA_HOSTTYPE_SOC) - iounmap(eromptr); - diff --git a/target/linux/generic/patches-3.3/028-bcma-fix-regression-in-interrupt-assignment-on-mips.patch b/target/linux/generic/patches-3.3/028-bcma-fix-regression-in-interrupt-assignment-on-mips.patch deleted file mode 100644 index 9386af29c..000000000 --- a/target/linux/generic/patches-3.3/028-bcma-fix-regression-in-interrupt-assignment-on-mips.patch +++ /dev/null @@ -1,29 +0,0 @@ ---- a/drivers/bcma/driver_mips.c -+++ b/drivers/bcma/driver_mips.c -@@ -131,7 +131,7 @@ static void bcma_core_mips_set_irq(struc - /* backplane irq line is in use, find out who uses - * it and set user to irq 0 - */ -- list_for_each_entry_reverse(core, &bus->cores, list) { -+ list_for_each_entry(core, &bus->cores, list) { - if ((1 << bcma_core_mips_irqflag(core)) == - oldirqflag) { - bcma_core_mips_set_irq(core, 0); -@@ -161,7 +161,7 @@ static void bcma_core_mips_dump_irq(stru - { - struct bcma_device *core; - -- list_for_each_entry_reverse(core, &bus->cores, list) { -+ list_for_each_entry(core, &bus->cores, list) { - bcma_core_mips_print_irq(core, bcma_core_mips_irq(core)); - } - } -@@ -215,7 +215,7 @@ void bcma_core_mips_init(struct bcma_drv - mcore->assigned_irqs = 1; - - /* Assign IRQs to all cores on the bus */ -- list_for_each_entry_reverse(core, &bus->cores, list) { -+ list_for_each_entry(core, &bus->cores, list) { - int mips_irq; - if (core->irq) - continue; diff --git a/target/linux/generic/patches-3.3/029-bcma-use-fallback-sprom-if-sprom-on-card-was-not-val.patch b/target/linux/generic/patches-3.3/029-bcma-use-fallback-sprom-if-sprom-on-card-was-not-val.patch deleted file mode 100644 index b6e648056..000000000 --- a/target/linux/generic/patches-3.3/029-bcma-use-fallback-sprom-if-sprom-on-card-was-not-val.patch +++ /dev/null @@ -1,15 +0,0 @@ ---- a/drivers/bcma/sprom.c -+++ b/drivers/bcma/sprom.c -@@ -591,8 +591,11 @@ int bcma_sprom_get(struct bcma_bus *bus) - bcma_chipco_bcm4331_ext_pa_lines_ctl(&bus->drv_cc, true); - - err = bcma_sprom_valid(sprom); -- if (err) -+ if (err) { -+ bcma_warn(bus, "invalid sprom read from the PCIe card, try to use fallback sprom\n"); -+ err = bcma_fill_sprom_with_fallback(bus, &bus->sprom); - goto out; -+ } - - bcma_sprom_extract_r8(bus, sprom); - diff --git a/target/linux/generic/patches-3.6/020-ssb_update.patch b/target/linux/generic/patches-3.6/020-ssb_update.patch new file mode 100644 index 000000000..e61be82fe --- /dev/null +++ b/target/linux/generic/patches-3.6/020-ssb_update.patch @@ -0,0 +1,82 @@ +--- a/drivers/ssb/driver_mipscore.c ++++ b/drivers/ssb/driver_mipscore.c +@@ -190,16 +190,32 @@ static void ssb_mips_flash_detect(struct + { + struct ssb_bus *bus = mcore->dev->bus; + +- mcore->flash_buswidth = 2; +- if (bus->chipco.dev) { +- mcore->flash_window = 0x1c000000; +- mcore->flash_window_size = 0x02000000; ++ /* When there is no chipcommon on the bus there is 4MB flash */ ++ if (!bus->chipco.dev) { ++ mcore->pflash.present = true; ++ mcore->pflash.buswidth = 2; ++ mcore->pflash.window = SSB_FLASH1; ++ mcore->pflash.window_size = SSB_FLASH1_SZ; ++ return; ++ } ++ ++ /* There is ChipCommon, so use it to read info about flash */ ++ switch (bus->chipco.capabilities & SSB_CHIPCO_CAP_FLASHT) { ++ case SSB_CHIPCO_FLASHT_STSER: ++ case SSB_CHIPCO_FLASHT_ATSER: ++ pr_err("Serial flash not supported\n"); ++ break; ++ case SSB_CHIPCO_FLASHT_PARA: ++ pr_debug("Found parallel flash\n"); ++ mcore->pflash.present = true; ++ mcore->pflash.window = SSB_FLASH2; ++ mcore->pflash.window_size = SSB_FLASH2_SZ; + if ((ssb_read32(bus->chipco.dev, SSB_CHIPCO_FLASH_CFG) + & SSB_CHIPCO_CFG_DS16) == 0) +- mcore->flash_buswidth = 1; +- } else { +- mcore->flash_window = 0x1fc00000; +- mcore->flash_window_size = 0x00400000; ++ mcore->pflash.buswidth = 1; ++ else ++ mcore->pflash.buswidth = 2; ++ break; + } + } + +--- a/include/linux/ssb/ssb_driver_chipcommon.h ++++ b/include/linux/ssb/ssb_driver_chipcommon.h +@@ -504,7 +504,9 @@ + #define SSB_CHIPCO_FLASHCTL_ST_SE 0x02D8 /* Sector Erase */ + #define SSB_CHIPCO_FLASHCTL_ST_BE 0x00C7 /* Bulk Erase */ + #define SSB_CHIPCO_FLASHCTL_ST_DP 0x00B9 /* Deep Power-down */ +-#define SSB_CHIPCO_FLASHCTL_ST_RSIG 0x03AB /* Read Electronic Signature */ ++#define SSB_CHIPCO_FLASHCTL_ST_RES 0x03AB /* Read Electronic Signature */ ++#define SSB_CHIPCO_FLASHCTL_ST_CSA 0x1000 /* Keep chip select asserted */ ++#define SSB_CHIPCO_FLASHCTL_ST_SSE 0x0220 /* Sub-sector Erase */ + + /* Status register bits for ST flashes */ + #define SSB_CHIPCO_FLASHSTA_ST_WIP 0x01 /* Write In Progress */ +--- a/include/linux/ssb/ssb_driver_mips.h ++++ b/include/linux/ssb/ssb_driver_mips.h +@@ -13,6 +13,12 @@ struct ssb_serial_port { + unsigned int reg_shift; + }; + ++struct ssb_pflash { ++ bool present; ++ u8 buswidth; ++ u32 window; ++ u32 window_size; ++}; + + struct ssb_mipscore { + struct ssb_device *dev; +@@ -20,9 +26,7 @@ struct ssb_mipscore { + int nr_serial_ports; + struct ssb_serial_port serial_ports[4]; + +- u8 flash_buswidth; +- u32 flash_window; +- u32 flash_window_size; ++ struct ssb_pflash pflash; + }; + + extern void ssb_mipscore_init(struct ssb_mipscore *mcore); diff --git a/target/linux/generic/patches-3.6/025-bcma_backport.patch b/target/linux/generic/patches-3.6/025-bcma_backport.patch new file mode 100644 index 000000000..d791f16a0 --- /dev/null +++ b/target/linux/generic/patches-3.6/025-bcma_backport.patch @@ -0,0 +1,1035 @@ +--- a/drivers/bcma/Kconfig ++++ b/drivers/bcma/Kconfig +@@ -48,12 +48,12 @@ config BCMA_DRIVER_MIPS + + config BCMA_SFLASH + bool +- depends on BCMA_DRIVER_MIPS && BROKEN ++ depends on BCMA_DRIVER_MIPS + default y + + config BCMA_NFLASH + bool +- depends on BCMA_DRIVER_MIPS && BROKEN ++ depends on BCMA_DRIVER_MIPS + default y + + config BCMA_DRIVER_GMAC_CMN +--- a/drivers/bcma/bcma_private.h ++++ b/drivers/bcma/bcma_private.h +@@ -54,6 +54,7 @@ u32 bcma_pmu_get_clockcpu(struct bcma_dr + #ifdef CONFIG_BCMA_SFLASH + /* driver_chipcommon_sflash.c */ + int bcma_sflash_init(struct bcma_drv_cc *cc); ++extern struct platform_device bcma_sflash_dev; + #else + static inline int bcma_sflash_init(struct bcma_drv_cc *cc) + { +@@ -65,6 +66,7 @@ static inline int bcma_sflash_init(struc + #ifdef CONFIG_BCMA_NFLASH + /* driver_chipcommon_nflash.c */ + int bcma_nflash_init(struct bcma_drv_cc *cc); ++extern struct platform_device bcma_nflash_dev; + #else + static inline int bcma_nflash_init(struct bcma_drv_cc *cc) + { +--- a/drivers/bcma/core.c ++++ b/drivers/bcma/core.c +@@ -65,7 +65,7 @@ void bcma_core_set_clockmode(struct bcma + switch (clkmode) { + case BCMA_CLKMODE_FAST: + bcma_set32(core, BCMA_CLKCTLST, BCMA_CLKCTLST_FORCEHT); +- udelay(64); ++ usleep_range(64, 300); + for (i = 0; i < 1500; i++) { + if (bcma_read32(core, BCMA_CLKCTLST) & + BCMA_CLKCTLST_HAVEHT) { +--- a/drivers/bcma/driver_chipcommon.c ++++ b/drivers/bcma/driver_chipcommon.c +@@ -22,12 +22,9 @@ static inline u32 bcma_cc_write32_masked + return value; + } + +-void bcma_core_chipcommon_init(struct bcma_drv_cc *cc) ++void bcma_core_chipcommon_early_init(struct bcma_drv_cc *cc) + { +- u32 leddc_on = 10; +- u32 leddc_off = 90; +- +- if (cc->setup_done) ++ if (cc->early_setup_done) + return; + + if (cc->core->id.rev >= 11) +@@ -36,6 +33,22 @@ void bcma_core_chipcommon_init(struct bc + if (cc->core->id.rev >= 35) + cc->capabilities_ext = bcma_cc_read32(cc, BCMA_CC_CAP_EXT); + ++ if (cc->capabilities & BCMA_CC_CAP_PMU) ++ bcma_pmu_early_init(cc); ++ ++ cc->early_setup_done = true; ++} ++ ++void bcma_core_chipcommon_init(struct bcma_drv_cc *cc) ++{ ++ u32 leddc_on = 10; ++ u32 leddc_off = 90; ++ ++ if (cc->setup_done) ++ return; ++ ++ bcma_core_chipcommon_early_init(cc); ++ + if (cc->core->id.rev >= 20) { + bcma_cc_write32(cc, BCMA_CC_GPIOPULLUP, 0); + bcma_cc_write32(cc, BCMA_CC_GPIOPULLDOWN, 0); +--- a/drivers/bcma/driver_chipcommon_nflash.c ++++ b/drivers/bcma/driver_chipcommon_nflash.c +@@ -5,15 +5,40 @@ + * Licensed under the GNU/GPL. See COPYING for details. + */ + ++#include <linux/platform_device.h> + #include <linux/bcma/bcma.h> +-#include <linux/bcma/bcma_driver_chipcommon.h> +-#include <linux/delay.h> + + #include "bcma_private.h" + ++struct platform_device bcma_nflash_dev = { ++ .name = "bcma_nflash", ++ .num_resources = 0, ++}; ++ + /* Initialize NAND flash access */ + int bcma_nflash_init(struct bcma_drv_cc *cc) + { +- bcma_err(cc->core->bus, "NAND flash support is broken\n"); ++ struct bcma_bus *bus = cc->core->bus; ++ ++ if (bus->chipinfo.id != BCMA_CHIP_ID_BCM4706 && ++ cc->core->id.rev != 0x38) { ++ bcma_err(bus, "NAND flash on unsupported board!\n"); ++ return -ENOTSUPP; ++ } ++ ++ if (!(cc->capabilities & BCMA_CC_CAP_NFLASH)) { ++ bcma_err(bus, "NAND flash not present according to ChipCommon\n"); ++ return -ENODEV; ++ } ++ ++ cc->nflash.present = true; ++ if (cc->core->id.rev == 38 && ++ (cc->status & BCMA_CC_CHIPST_5357_NAND_BOOT)) ++ cc->nflash.boot = true; ++ ++ /* Prepare platform device, but don't register it yet. It's too early, ++ * malloc (required by device_private_init) is not available yet. */ ++ bcma_nflash_dev.dev.platform_data = &cc->nflash; ++ + return 0; + } +--- a/drivers/bcma/driver_chipcommon_pmu.c ++++ b/drivers/bcma/driver_chipcommon_pmu.c +@@ -76,7 +76,10 @@ static void bcma_pmu_resources_init(stru + if (max_msk) + bcma_cc_write32(cc, BCMA_CC_PMU_MAXRES_MSK, max_msk); + +- /* Add some delay; allow resources to come up and settle. */ ++ /* ++ * Add some delay; allow resources to come up and settle. ++ * Delay is required for SoC (early init). ++ */ + mdelay(2); + } + +@@ -101,7 +104,7 @@ void bcma_chipco_bcm4331_ext_pa_lines_ct + bcma_cc_write32(cc, BCMA_CC_CHIPCTL, val); + } + +-void bcma_pmu_workarounds(struct bcma_drv_cc *cc) ++static void bcma_pmu_workarounds(struct bcma_drv_cc *cc) + { + struct bcma_bus *bus = cc->core->bus; + +@@ -141,7 +144,7 @@ void bcma_pmu_workarounds(struct bcma_dr + } + } + +-void bcma_pmu_init(struct bcma_drv_cc *cc) ++void bcma_pmu_early_init(struct bcma_drv_cc *cc) + { + u32 pmucap; + +@@ -150,7 +153,10 @@ void bcma_pmu_init(struct bcma_drv_cc *c + + bcma_debug(cc->core->bus, "Found rev %u PMU (capabilities 0x%08X)\n", + cc->pmu.rev, pmucap); ++} + ++void bcma_pmu_init(struct bcma_drv_cc *cc) ++{ + if (cc->pmu.rev == 1) + bcma_cc_mask32(cc, BCMA_CC_PMU_CTL, + ~BCMA_CC_PMU_CTL_NOILPONW); +@@ -257,7 +263,7 @@ static u32 bcma_pmu_clock_bcm4706(struct + } + + /* query bus clock frequency for PMU-enabled chipcommon */ +-u32 bcma_pmu_get_clockcontrol(struct bcma_drv_cc *cc) ++static u32 bcma_pmu_get_clockcontrol(struct bcma_drv_cc *cc) + { + struct bcma_bus *bus = cc->core->bus; + +--- a/drivers/bcma/driver_chipcommon_sflash.c ++++ b/drivers/bcma/driver_chipcommon_sflash.c +@@ -5,15 +5,161 @@ + * Licensed under the GNU/GPL. See COPYING for details. + */ + ++#include <linux/platform_device.h> + #include <linux/bcma/bcma.h> +-#include <linux/bcma/bcma_driver_chipcommon.h> +-#include <linux/delay.h> + + #include "bcma_private.h" + ++static struct resource bcma_sflash_resource = { ++ .name = "bcma_sflash", ++ .start = BCMA_SOC_FLASH2, ++ .end = 0, ++ .flags = IORESOURCE_MEM | IORESOURCE_READONLY, ++}; ++ ++struct platform_device bcma_sflash_dev = { ++ .name = "bcma_sflash", ++ .resource = &bcma_sflash_resource, ++ .num_resources = 1, ++}; ++ ++struct bcma_sflash_tbl_e { ++ char *name; ++ u32 id; ++ u32 blocksize; ++ u16 numblocks; ++}; ++ ++static struct bcma_sflash_tbl_e bcma_sflash_st_tbl[] = { ++ { "M25P20", 0x11, 0x10000, 4, }, ++ { "M25P40", 0x12, 0x10000, 8, }, ++ ++ { "M25P16", 0x14, 0x10000, 32, }, ++ { "M25P32", 0x14, 0x10000, 64, }, ++ { "M25P64", 0x16, 0x10000, 128, }, ++ { "M25FL128", 0x17, 0x10000, 256, }, ++ { 0 }, ++}; ++ ++static struct bcma_sflash_tbl_e bcma_sflash_sst_tbl[] = { ++ { "SST25WF512", 1, 0x1000, 16, }, ++ { "SST25VF512", 0x48, 0x1000, 16, }, ++ { "SST25WF010", 2, 0x1000, 32, }, ++ { "SST25VF010", 0x49, 0x1000, 32, }, ++ { "SST25WF020", 3, 0x1000, 64, }, ++ { "SST25VF020", 0x43, 0x1000, 64, }, ++ { "SST25WF040", 4, 0x1000, 128, }, ++ { "SST25VF040", 0x44, 0x1000, 128, }, ++ { "SST25VF040B", 0x8d, 0x1000, 128, }, ++ { "SST25WF080", 5, 0x1000, 256, }, ++ { "SST25VF080B", 0x8e, 0x1000, 256, }, ++ { "SST25VF016", 0x41, 0x1000, 512, }, ++ { "SST25VF032", 0x4a, 0x1000, 1024, }, ++ { "SST25VF064", 0x4b, 0x1000, 2048, }, ++ { 0 }, ++}; ++ ++static struct bcma_sflash_tbl_e bcma_sflash_at_tbl[] = { ++ { "AT45DB011", 0xc, 256, 512, }, ++ { "AT45DB021", 0x14, 256, 1024, }, ++ { "AT45DB041", 0x1c, 256, 2048, }, ++ { "AT45DB081", 0x24, 256, 4096, }, ++ { "AT45DB161", 0x2c, 512, 4096, }, ++ { "AT45DB321", 0x34, 512, 8192, }, ++ { "AT45DB642", 0x3c, 1024, 8192, }, ++ { 0 }, ++}; ++ ++static void bcma_sflash_cmd(struct bcma_drv_cc *cc, u32 opcode) ++{ ++ int i; ++ bcma_cc_write32(cc, BCMA_CC_FLASHCTL, ++ BCMA_CC_FLASHCTL_START | opcode); ++ for (i = 0; i < 1000; i++) { ++ if (!(bcma_cc_read32(cc, BCMA_CC_FLASHCTL) & ++ BCMA_CC_FLASHCTL_BUSY)) ++ return; ++ cpu_relax(); ++ } ++ bcma_err(cc->core->bus, "SFLASH control command failed (timeout)!\n"); ++} ++ + /* Initialize serial flash access */ + int bcma_sflash_init(struct bcma_drv_cc *cc) + { +- bcma_err(cc->core->bus, "Serial flash support is broken\n"); ++ struct bcma_bus *bus = cc->core->bus; ++ struct bcma_sflash *sflash = &cc->sflash; ++ struct bcma_sflash_tbl_e *e; ++ u32 id, id2; ++ ++ switch (cc->capabilities & BCMA_CC_CAP_FLASHT) { ++ case BCMA_CC_FLASHT_STSER: ++ bcma_sflash_cmd(cc, BCMA_CC_FLASHCTL_ST_DP); ++ ++ bcma_cc_write32(cc, BCMA_CC_FLASHADDR, 0); ++ bcma_sflash_cmd(cc, BCMA_CC_FLASHCTL_ST_RES); ++ id = bcma_cc_read32(cc, BCMA_CC_FLASHDATA); ++ ++ bcma_cc_write32(cc, BCMA_CC_FLASHADDR, 1); ++ bcma_sflash_cmd(cc, BCMA_CC_FLASHCTL_ST_RES); ++ id2 = bcma_cc_read32(cc, BCMA_CC_FLASHDATA); ++ ++ switch (id) { ++ case 0xbf: ++ for (e = bcma_sflash_sst_tbl; e->name; e++) { ++ if (e->id == id2) ++ break; ++ } ++ break; ++ case 0x13: ++ return -ENOTSUPP; ++ default: ++ for (e = bcma_sflash_st_tbl; e->name; e++) { ++ if (e->id == id) ++ break; ++ } ++ break; ++ } ++ if (!e->name) { ++ bcma_err(bus, "Unsupported ST serial flash (id: 0x%X, id2: 0x%X)\n", id, id2); ++ return -ENOTSUPP; ++ } ++ ++ break; ++ case BCMA_CC_FLASHT_ATSER: ++ bcma_sflash_cmd(cc, BCMA_CC_FLASHCTL_AT_STATUS); ++ id = bcma_cc_read32(cc, BCMA_CC_FLASHDATA) & 0x3c; ++ ++ for (e = bcma_sflash_at_tbl; e->name; e++) { ++ if (e->id == id) ++ break; ++ } ++ if (!e->name) { ++ bcma_err(bus, "Unsupported Atmel serial flash (id: 0x%X)\n", id); ++ return -ENOTSUPP; ++ } ++ ++ break; ++ default: ++ bcma_err(bus, "Unsupported flash type\n"); ++ return -ENOTSUPP; ++ } ++ ++ sflash->window = BCMA_SOC_FLASH2; ++ sflash->blocksize = e->blocksize; ++ sflash->numblocks = e->numblocks; ++ sflash->size = sflash->blocksize * sflash->numblocks; ++ sflash->present = true; ++ ++ bcma_info(bus, "Found %s serial flash (size: %dKiB, blocksize: 0x%X, blocks: %d)\n", ++ e->name, sflash->size / 1024, sflash->blocksize, ++ sflash->numblocks); ++ ++ /* Prepare platform device, but don't register it yet. It's too early, ++ * malloc (required by device_private_init) is not available yet. */ ++ bcma_sflash_dev.resource[0].end = bcma_sflash_dev.resource[0].start + ++ sflash->size; ++ bcma_sflash_dev.dev.platform_data = sflash; ++ + return 0; + } +--- a/drivers/bcma/driver_mips.c ++++ b/drivers/bcma/driver_mips.c +@@ -181,47 +181,66 @@ EXPORT_SYMBOL(bcma_cpu_clock); + static void bcma_core_mips_flash_detect(struct bcma_drv_mips *mcore) + { + struct bcma_bus *bus = mcore->core->bus; ++ struct bcma_drv_cc *cc = &bus->drv_cc; + +- switch (bus->drv_cc.capabilities & BCMA_CC_CAP_FLASHT) { ++ switch (cc->capabilities & BCMA_CC_CAP_FLASHT) { + case BCMA_CC_FLASHT_STSER: + case BCMA_CC_FLASHT_ATSER: + bcma_debug(bus, "Found serial flash\n"); +- bcma_sflash_init(&bus->drv_cc); ++ bcma_sflash_init(cc); + break; + case BCMA_CC_FLASHT_PARA: + bcma_debug(bus, "Found parallel flash\n"); +- bus->drv_cc.pflash.window = 0x1c000000; +- bus->drv_cc.pflash.window_size = 0x02000000; ++ cc->pflash.present = true; ++ cc->pflash.window = BCMA_SOC_FLASH2; ++ cc->pflash.window_size = BCMA_SOC_FLASH2_SZ; + +- if ((bcma_read32(bus->drv_cc.core, BCMA_CC_FLASH_CFG) & ++ if ((bcma_read32(cc->core, BCMA_CC_FLASH_CFG) & + BCMA_CC_FLASH_CFG_DS) == 0) +- bus->drv_cc.pflash.buswidth = 1; ++ cc->pflash.buswidth = 1; + else +- bus->drv_cc.pflash.buswidth = 2; ++ cc->pflash.buswidth = 2; + break; + default: + bcma_err(bus, "Flash type not supported\n"); + } + +- if (bus->drv_cc.core->id.rev == 38 || ++ if (cc->core->id.rev == 38 || + bus->chipinfo.id == BCMA_CHIP_ID_BCM4706) { +- if (bus->drv_cc.capabilities & BCMA_CC_CAP_NFLASH) { ++ if (cc->capabilities & BCMA_CC_CAP_NFLASH) { + bcma_debug(bus, "Found NAND flash\n"); +- bcma_nflash_init(&bus->drv_cc); ++ bcma_nflash_init(cc); + } + } + } + ++void bcma_core_mips_early_init(struct bcma_drv_mips *mcore) ++{ ++ struct bcma_bus *bus = mcore->core->bus; ++ ++ if (mcore->early_setup_done) ++ return; ++ ++ bcma_chipco_serial_init(&bus->drv_cc); ++ bcma_core_mips_flash_detect(mcore); ++ ++ mcore->early_setup_done = true; ++} ++ + void bcma_core_mips_init(struct bcma_drv_mips *mcore) + { + struct bcma_bus *bus; + struct bcma_device *core; + bus = mcore->core->bus; + ++ if (mcore->setup_done) ++ return; ++ + bcma_info(bus, "Initializing MIPS core...\n"); + +- if (!mcore->setup_done) +- mcore->assigned_irqs = 1; ++ bcma_core_mips_early_init(mcore); ++ ++ mcore->assigned_irqs = 1; + + /* Assign IRQs to all cores on the bus */ + list_for_each_entry(core, &bus->cores, list) { +@@ -256,10 +275,5 @@ void bcma_core_mips_init(struct bcma_drv + bcma_info(bus, "IRQ reconfiguration done\n"); + bcma_core_mips_dump_irq(bus); + +- if (mcore->setup_done) +- return; +- +- bcma_chipco_serial_init(&bus->drv_cc); +- bcma_core_mips_flash_detect(mcore); + mcore->setup_done = true; + } +--- a/drivers/bcma/driver_pci.c ++++ b/drivers/bcma/driver_pci.c +@@ -51,7 +51,7 @@ static void bcma_pcie_mdio_set_phy(struc + v = pcicore_read32(pc, BCMA_CORE_PCI_MDIO_CONTROL); + if (v & BCMA_CORE_PCI_MDIOCTL_ACCESS_DONE) + break; +- msleep(1); ++ usleep_range(1000, 2000); + } + } + +@@ -92,7 +92,7 @@ static u16 bcma_pcie_mdio_read(struct bc + ret = pcicore_read32(pc, BCMA_CORE_PCI_MDIO_DATA); + break; + } +- msleep(1); ++ usleep_range(1000, 2000); + } + pcicore_write32(pc, BCMA_CORE_PCI_MDIO_CONTROL, 0); + return ret; +@@ -132,7 +132,7 @@ static void bcma_pcie_mdio_write(struct + v = pcicore_read32(pc, BCMA_CORE_PCI_MDIO_CONTROL); + if (v & BCMA_CORE_PCI_MDIOCTL_ACCESS_DONE) + break; +- msleep(1); ++ usleep_range(1000, 2000); + } + pcicore_write32(pc, BCMA_CORE_PCI_MDIO_CONTROL, 0); + } +--- a/drivers/bcma/driver_pci_host.c ++++ b/drivers/bcma/driver_pci_host.c +@@ -35,11 +35,6 @@ bool __devinit bcma_core_pci_is_in_hostm + chipid_top != 0x5300) + return false; + +- if (bus->sprom.boardflags_lo & BCMA_CORE_PCI_BFL_NOPCI) { +- bcma_info(bus, "This PCI core is disabled and not working\n"); +- return false; +- } +- + bcma_core_enable(pc->core, 0); + + return !mips_busprobe32(tmp, pc->core->io_addr); +@@ -396,6 +391,11 @@ void __devinit bcma_core_pci_hostmode_in + + bcma_info(bus, "PCIEcore in host mode found\n"); + ++ if (bus->sprom.boardflags_lo & BCMA_CORE_PCI_BFL_NOPCI) { ++ bcma_info(bus, "This PCIE core is disabled and not working\n"); ++ return; ++ } ++ + pc_host = kzalloc(sizeof(*pc_host), GFP_KERNEL); + if (!pc_host) { + bcma_err(bus, "can not allocate memory"); +@@ -425,9 +425,9 @@ void __devinit bcma_core_pci_hostmode_in + pc_host->io_resource.flags = IORESOURCE_IO | IORESOURCE_PCI_FIXED; + + /* Reset RC */ +- udelay(3000); ++ usleep_range(3000, 5000); + pcicore_write32(pc, BCMA_CORE_PCI_CTL, BCMA_CORE_PCI_CTL_RST_OE); +- udelay(1000); ++ usleep_range(1000, 2000); + pcicore_write32(pc, BCMA_CORE_PCI_CTL, BCMA_CORE_PCI_CTL_RST | + BCMA_CORE_PCI_CTL_RST_OE); + +@@ -452,6 +452,8 @@ void __devinit bcma_core_pci_hostmode_in + pc_host->mem_resource.start = BCMA_SOC_PCI_MEM; + pc_host->mem_resource.end = BCMA_SOC_PCI_MEM + + BCMA_SOC_PCI_MEM_SZ - 1; ++ pc_host->io_resource.start = 0x100; ++ pc_host->io_resource.end = 0x47F; + pci_membase_1G = BCMA_SOC_PCIE_DMA_H32; + pcicore_write32(pc, BCMA_CORE_PCI_SBTOPCI0, + tmp | BCMA_SOC_PCI_MEM); +@@ -459,6 +461,8 @@ void __devinit bcma_core_pci_hostmode_in + pc_host->mem_resource.start = BCMA_SOC_PCI1_MEM; + pc_host->mem_resource.end = BCMA_SOC_PCI1_MEM + + BCMA_SOC_PCI_MEM_SZ - 1; ++ pc_host->io_resource.start = 0x480; ++ pc_host->io_resource.end = 0x7FF; + pci_membase_1G = BCMA_SOC_PCIE1_DMA_H32; + pc_host->host_cfg_addr = BCMA_SOC_PCI1_CFG; + pcicore_write32(pc, BCMA_CORE_PCI_SBTOPCI0, +@@ -481,7 +485,7 @@ void __devinit bcma_core_pci_hostmode_in + * before issuing configuration requests to PCI Express + * devices. + */ +- udelay(100000); ++ msleep(100); + + bcma_core_pci_enable_crs(pc); + +@@ -501,7 +505,7 @@ void __devinit bcma_core_pci_hostmode_in + set_io_port_base(pc_host->pci_controller.io_map_base); + /* Give some time to the PCI controller to configure itself with the new + * values. Not waiting at this point causes crashes of the machine. */ +- mdelay(10); ++ usleep_range(10000, 15000); + register_pci_controller(&pc_host->pci_controller); + return; + } +--- a/drivers/bcma/host_pci.c ++++ b/drivers/bcma/host_pci.c +@@ -77,8 +77,8 @@ static void bcma_host_pci_write32(struct + } + + #ifdef CONFIG_BCMA_BLOCKIO +-void bcma_host_pci_block_read(struct bcma_device *core, void *buffer, +- size_t count, u16 offset, u8 reg_width) ++static void bcma_host_pci_block_read(struct bcma_device *core, void *buffer, ++ size_t count, u16 offset, u8 reg_width) + { + void __iomem *addr = core->bus->mmio + offset; + if (core->bus->mapped_core != core) +@@ -100,8 +100,9 @@ void bcma_host_pci_block_read(struct bcm + } + } + +-void bcma_host_pci_block_write(struct bcma_device *core, const void *buffer, +- size_t count, u16 offset, u8 reg_width) ++static void bcma_host_pci_block_write(struct bcma_device *core, ++ const void *buffer, size_t count, ++ u16 offset, u8 reg_width) + { + void __iomem *addr = core->bus->mmio + offset; + if (core->bus->mapped_core != core) +@@ -139,7 +140,7 @@ static void bcma_host_pci_awrite32(struc + iowrite32(value, core->bus->mmio + (1 * BCMA_CORE_SIZE) + offset); + } + +-const struct bcma_host_ops bcma_host_pci_ops = { ++static const struct bcma_host_ops bcma_host_pci_ops = { + .read8 = bcma_host_pci_read8, + .read16 = bcma_host_pci_read16, + .read32 = bcma_host_pci_read32, +@@ -272,6 +273,7 @@ static DEFINE_PCI_DEVICE_TABLE(bcma_pci_ + { PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, 0x4331) }, + { PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, 0x4353) }, + { PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, 0x4357) }, ++ { PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, 0x4358) }, + { PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, 0x4359) }, + { PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, 0x4727) }, + { 0, }, +--- a/drivers/bcma/host_soc.c ++++ b/drivers/bcma/host_soc.c +@@ -143,7 +143,7 @@ static void bcma_host_soc_awrite32(struc + writel(value, core->io_wrap + offset); + } + +-const struct bcma_host_ops bcma_host_soc_ops = { ++static const struct bcma_host_ops bcma_host_soc_ops = { + .read8 = bcma_host_soc_read8, + .read16 = bcma_host_soc_read16, + .read32 = bcma_host_soc_read32, +--- a/drivers/bcma/main.c ++++ b/drivers/bcma/main.c +@@ -7,6 +7,7 @@ + + #include "bcma_private.h" + #include <linux/module.h> ++#include <linux/platform_device.h> + #include <linux/bcma/bcma.h> + #include <linux/slab.h> + +@@ -80,6 +81,18 @@ struct bcma_device *bcma_find_core(struc + } + EXPORT_SYMBOL_GPL(bcma_find_core); + ++static struct bcma_device *bcma_find_core_unit(struct bcma_bus *bus, u16 coreid, ++ u8 unit) ++{ ++ struct bcma_device *core; ++ ++ list_for_each_entry(core, &bus->cores, list) { ++ if (core->id.id == coreid && core->core_unit == unit) ++ return core; ++ } ++ return NULL; ++} ++ + static void bcma_release_core_dev(struct device *dev) + { + struct bcma_device *core = container_of(dev, struct bcma_device, dev); +@@ -136,14 +149,31 @@ static int bcma_register_cores(struct bc + dev_id++; + } + ++#ifdef CONFIG_BCMA_SFLASH ++ if (bus->drv_cc.sflash.present) { ++ err = platform_device_register(&bcma_sflash_dev); ++ if (err) ++ bcma_err(bus, "Error registering serial flash\n"); ++ } ++#endif ++ ++#ifdef CONFIG_BCMA_NFLASH ++ if (bus->drv_cc.nflash.present) { ++ err = platform_device_register(&bcma_nflash_dev); ++ if (err) ++ bcma_err(bus, "Error registering NAND flash\n"); ++ } ++#endif ++ + return 0; + } + + static void bcma_unregister_cores(struct bcma_bus *bus) + { +- struct bcma_device *core; ++ struct bcma_device *core, *tmp; + +- list_for_each_entry(core, &bus->cores, list) { ++ list_for_each_entry_safe(core, tmp, &bus->cores, list) { ++ list_del(&core->list); + if (core->dev_registered) + device_unregister(&core->dev); + } +@@ -165,6 +195,20 @@ int __devinit bcma_bus_register(struct b + return -1; + } + ++ /* Early init CC core */ ++ core = bcma_find_core(bus, bcma_cc_core_id(bus)); ++ if (core) { ++ bus->drv_cc.core = core; ++ bcma_core_chipcommon_early_init(&bus->drv_cc); ++ } ++ ++ /* Try to get SPROM */ ++ err = bcma_sprom_get(bus); ++ if (err == -ENOENT) { ++ bcma_err(bus, "No SPROM available\n"); ++ } else if (err) ++ bcma_err(bus, "Failed to get SPROM: %d\n", err); ++ + /* Init CC core */ + core = bcma_find_core(bus, bcma_cc_core_id(bus)); + if (core) { +@@ -180,10 +224,17 @@ int __devinit bcma_bus_register(struct b + } + + /* Init PCIE core */ +- core = bcma_find_core(bus, BCMA_CORE_PCIE); ++ core = bcma_find_core_unit(bus, BCMA_CORE_PCIE, 0); + if (core) { +- bus->drv_pci.core = core; +- bcma_core_pci_init(&bus->drv_pci); ++ bus->drv_pci[0].core = core; ++ bcma_core_pci_init(&bus->drv_pci[0]); ++ } ++ ++ /* Init PCIE core */ ++ core = bcma_find_core_unit(bus, BCMA_CORE_PCIE, 1); ++ if (core) { ++ bus->drv_pci[1].core = core; ++ bcma_core_pci_init(&bus->drv_pci[1]); + } + + /* Init GBIT MAC COMMON core */ +@@ -193,13 +244,6 @@ int __devinit bcma_bus_register(struct b + bcma_core_gmac_cmn_init(&bus->drv_gmac_cmn); + } + +- /* Try to get SPROM */ +- err = bcma_sprom_get(bus); +- if (err == -ENOENT) { +- bcma_err(bus, "No SPROM available\n"); +- } else if (err) +- bcma_err(bus, "Failed to get SPROM: %d\n", err); +- + /* Register found cores */ + bcma_register_cores(bus); + +@@ -210,7 +254,17 @@ int __devinit bcma_bus_register(struct b + + void bcma_bus_unregister(struct bcma_bus *bus) + { ++ struct bcma_device *cores[3]; ++ ++ cores[0] = bcma_find_core(bus, BCMA_CORE_MIPS_74K); ++ cores[1] = bcma_find_core(bus, BCMA_CORE_PCIE); ++ cores[2] = bcma_find_core(bus, BCMA_CORE_4706_MAC_GBIT_COMMON); ++ + bcma_unregister_cores(bus); ++ ++ kfree(cores[2]); ++ kfree(cores[1]); ++ kfree(cores[0]); + } + + int __init bcma_bus_early_register(struct bcma_bus *bus, +@@ -247,18 +301,18 @@ int __init bcma_bus_early_register(struc + return -1; + } + +- /* Init CC core */ ++ /* Early init CC core */ + core = bcma_find_core(bus, bcma_cc_core_id(bus)); + if (core) { + bus->drv_cc.core = core; +- bcma_core_chipcommon_init(&bus->drv_cc); ++ bcma_core_chipcommon_early_init(&bus->drv_cc); + } + +- /* Init MIPS core */ ++ /* Early init MIPS core */ + core = bcma_find_core(bus, BCMA_CORE_MIPS_74K); + if (core) { + bus->drv_mips.core = core; +- bcma_core_mips_init(&bus->drv_mips); ++ bcma_core_mips_early_init(&bus->drv_mips); + } + + bcma_info(bus, "Early bus registered\n"); +--- a/drivers/bcma/sprom.c ++++ b/drivers/bcma/sprom.c +@@ -507,7 +507,9 @@ static bool bcma_sprom_onchip_available( + /* for these chips OTP is always available */ + present = true; + break; ++ case BCMA_CHIP_ID_BCM43227: + case BCMA_CHIP_ID_BCM43228: ++ case BCMA_CHIP_ID_BCM43428: + present = chip_status & BCMA_CC_CHIPST_43228_OTP_PRESENT; + break; + default: +@@ -593,8 +595,11 @@ int bcma_sprom_get(struct bcma_bus *bus) + bcma_chipco_bcm4331_ext_pa_lines_ctl(&bus->drv_cc, true); + + err = bcma_sprom_valid(sprom); +- if (err) ++ if (err) { ++ bcma_warn(bus, "invalid sprom read from the PCIe card, try to use fallback sprom\n"); ++ err = bcma_fill_sprom_with_fallback(bus, &bus->sprom); + goto out; ++ } + + bcma_sprom_extract_r8(bus, sprom); + +--- a/include/linux/bcma/bcma.h ++++ b/include/linux/bcma/bcma.h +@@ -10,7 +10,7 @@ + #include <linux/bcma/bcma_driver_gmac_cmn.h> + #include <linux/ssb/ssb.h> /* SPROM sharing */ + +-#include "bcma_regs.h" ++#include <linux/bcma/bcma_regs.h> + + struct bcma_device; + struct bcma_bus; +@@ -251,7 +251,7 @@ struct bcma_bus { + u8 num; + + struct bcma_drv_cc drv_cc; +- struct bcma_drv_pci drv_pci; ++ struct bcma_drv_pci drv_pci[2]; + struct bcma_drv_mips drv_mips; + struct bcma_drv_gmac_cmn drv_gmac_cmn; + +--- a/include/linux/bcma/bcma_driver_chipcommon.h ++++ b/include/linux/bcma/bcma_driver_chipcommon.h +@@ -100,6 +100,7 @@ + #define BCMA_CC_CHIPST_4706_SFLASH_TYPE BIT(2) /* 0: 8b-p/ST-s flash, 1: 16b-p/Atmal-s flash */ + #define BCMA_CC_CHIPST_4706_MIPS_BENDIAN BIT(3) /* 0: little, 1: big endian */ + #define BCMA_CC_CHIPST_4706_PCIE1_DISABLE BIT(5) /* PCIE1 enable strap pin */ ++#define BCMA_CC_CHIPST_5357_NAND_BOOT BIT(4) /* NAND boot, valid for CC rev 38 and/or BCM5357 */ + #define BCMA_CC_JCMD 0x0030 /* Rev >= 10 only */ + #define BCMA_CC_JCMD_START 0x80000000 + #define BCMA_CC_JCMD_BUSY 0x80000000 +@@ -266,6 +267,29 @@ + #define BCMA_CC_SROM_CONTROL_SIZE_16K 0x00000004 + #define BCMA_CC_SROM_CONTROL_SIZE_SHIFT 1 + #define BCMA_CC_SROM_CONTROL_PRESENT 0x00000001 ++/* Block 0x140 - 0x190 registers are chipset specific */ ++#define BCMA_CC_4706_FLASHSCFG 0x18C /* Flash struct configuration */ ++#define BCMA_CC_4706_FLASHSCFG_MASK 0x000000ff ++#define BCMA_CC_4706_FLASHSCFG_SF1 0x00000001 /* 2nd serial flash present */ ++#define BCMA_CC_4706_FLASHSCFG_PF1 0x00000002 /* 2nd parallel flash present */ ++#define BCMA_CC_4706_FLASHSCFG_SF1_TYPE 0x00000004 /* 2nd serial flash type : 0 : ST, 1 : Atmel */ ++#define BCMA_CC_4706_FLASHSCFG_NF1 0x00000008 /* 2nd NAND flash present */ ++#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_MASK 0x000000f0 ++#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_4MB 0x00000010 /* 4MB */ ++#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_8MB 0x00000020 /* 8MB */ ++#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_16MB 0x00000030 /* 16MB */ ++#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_32MB 0x00000040 /* 32MB */ ++#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_64MB 0x00000050 /* 64MB */ ++#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_128MB 0x00000060 /* 128MB */ ++#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_256MB 0x00000070 /* 256MB */ ++/* NAND flash registers for BCM4706 (corerev = 31) */ ++#define BCMA_CC_NFLASH_CTL 0x01A0 ++#define BCMA_CC_NFLASH_CTL_ERR 0x08000000 ++#define BCMA_CC_NFLASH_CONF 0x01A4 ++#define BCMA_CC_NFLASH_COL_ADDR 0x01A8 ++#define BCMA_CC_NFLASH_ROW_ADDR 0x01AC ++#define BCMA_CC_NFLASH_DATA 0x01B0 ++#define BCMA_CC_NFLASH_WAITCNT0 0x01B4 + /* 0x1E0 is defined as shared BCMA_CLKCTLST */ + #define BCMA_CC_HW_WORKAROUND 0x01E4 /* Hardware workaround (rev >= 20) */ + #define BCMA_CC_UART0_DATA 0x0300 +@@ -325,6 +349,60 @@ + #define BCMA_CC_PLLCTL_ADDR 0x0660 + #define BCMA_CC_PLLCTL_DATA 0x0664 + #define BCMA_CC_SPROM 0x0800 /* SPROM beginning */ ++/* NAND flash MLC controller registers (corerev >= 38) */ ++#define BCMA_CC_NAND_REVISION 0x0C00 ++#define BCMA_CC_NAND_CMD_START 0x0C04 ++#define BCMA_CC_NAND_CMD_ADDR_X 0x0C08 ++#define BCMA_CC_NAND_CMD_ADDR 0x0C0C ++#define BCMA_CC_NAND_CMD_END_ADDR 0x0C10 ++#define BCMA_CC_NAND_CS_NAND_SELECT 0x0C14 ++#define BCMA_CC_NAND_CS_NAND_XOR 0x0C18 ++#define BCMA_CC_NAND_SPARE_RD0 0x0C20 ++#define BCMA_CC_NAND_SPARE_RD4 0x0C24 ++#define BCMA_CC_NAND_SPARE_RD8 0x0C28 ++#define BCMA_CC_NAND_SPARE_RD12 0x0C2C ++#define BCMA_CC_NAND_SPARE_WR0 0x0C30 ++#define BCMA_CC_NAND_SPARE_WR4 0x0C34 ++#define BCMA_CC_NAND_SPARE_WR8 0x0C38 ++#define BCMA_CC_NAND_SPARE_WR12 0x0C3C ++#define BCMA_CC_NAND_ACC_CONTROL 0x0C40 ++#define BCMA_CC_NAND_CONFIG 0x0C48 ++#define BCMA_CC_NAND_TIMING_1 0x0C50 ++#define BCMA_CC_NAND_TIMING_2 0x0C54 ++#define BCMA_CC_NAND_SEMAPHORE 0x0C58 ++#define BCMA_CC_NAND_DEVID 0x0C60 ++#define BCMA_CC_NAND_DEVID_X 0x0C64 ++#define BCMA_CC_NAND_BLOCK_LOCK_STATUS 0x0C68 ++#define BCMA_CC_NAND_INTFC_STATUS 0x0C6C ++#define BCMA_CC_NAND_ECC_CORR_ADDR_X 0x0C70 ++#define BCMA_CC_NAND_ECC_CORR_ADDR 0x0C74 ++#define BCMA_CC_NAND_ECC_UNC_ADDR_X 0x0C78 ++#define BCMA_CC_NAND_ECC_UNC_ADDR 0x0C7C ++#define BCMA_CC_NAND_READ_ERROR_COUNT 0x0C80 ++#define BCMA_CC_NAND_CORR_STAT_THRESHOLD 0x0C84 ++#define BCMA_CC_NAND_READ_ADDR_X 0x0C90 ++#define BCMA_CC_NAND_READ_ADDR 0x0C94 ++#define BCMA_CC_NAND_PAGE_PROGRAM_ADDR_X 0x0C98 ++#define BCMA_CC_NAND_PAGE_PROGRAM_ADDR 0x0C9C ++#define BCMA_CC_NAND_COPY_BACK_ADDR_X 0x0CA0 ++#define BCMA_CC_NAND_COPY_BACK_ADDR 0x0CA4 ++#define BCMA_CC_NAND_BLOCK_ERASE_ADDR_X 0x0CA8 ++#define BCMA_CC_NAND_BLOCK_ERASE_ADDR 0x0CAC ++#define BCMA_CC_NAND_INV_READ_ADDR_X 0x0CB0 ++#define BCMA_CC_NAND_INV_READ_ADDR 0x0CB4 ++#define BCMA_CC_NAND_BLK_WR_PROTECT 0x0CC0 ++#define BCMA_CC_NAND_ACC_CONTROL_CS1 0x0CD0 ++#define BCMA_CC_NAND_CONFIG_CS1 0x0CD4 ++#define BCMA_CC_NAND_TIMING_1_CS1 0x0CD8 ++#define BCMA_CC_NAND_TIMING_2_CS1 0x0CDC ++#define BCMA_CC_NAND_SPARE_RD16 0x0D30 ++#define BCMA_CC_NAND_SPARE_RD20 0x0D34 ++#define BCMA_CC_NAND_SPARE_RD24 0x0D38 ++#define BCMA_CC_NAND_SPARE_RD28 0x0D3C ++#define BCMA_CC_NAND_CACHE_ADDR 0x0D40 ++#define BCMA_CC_NAND_CACHE_DATA 0x0D44 ++#define BCMA_CC_NAND_CTRL_CONFIG 0x0D48 ++#define BCMA_CC_NAND_CTRL_STATUS 0x0D4C + + /* Divider allocation in 4716/47162/5356 */ + #define BCMA_CC_PMU5_MAINPLL_CPU 1 +@@ -415,6 +493,13 @@ + /* 4313 Chip specific ChipControl register bits */ + #define BCMA_CCTRL_4313_12MA_LED_DRIVE 0x00000007 /* 12 mA drive strengh for later 4313 */ + ++/* BCM5357 ChipControl register bits */ ++#define BCMA_CHIPCTL_5357_EXTPA BIT(14) ++#define BCMA_CHIPCTL_5357_ANT_MUX_2O3 BIT(15) ++#define BCMA_CHIPCTL_5357_NFLASH BIT(16) ++#define BCMA_CHIPCTL_5357_I2S_PINS_ENABLE BIT(18) ++#define BCMA_CHIPCTL_5357_I2CSPI_PINS_ENABLE BIT(19) ++ + /* Data for the PMU, if available. + * Check availability with ((struct bcma_chipcommon)->capabilities & BCMA_CC_CAP_PMU) + */ +@@ -425,11 +510,35 @@ struct bcma_chipcommon_pmu { + + #ifdef CONFIG_BCMA_DRIVER_MIPS + struct bcma_pflash { ++ bool present; + u8 buswidth; + u32 window; + u32 window_size; + }; + ++#ifdef CONFIG_BCMA_SFLASH ++struct bcma_sflash { ++ bool present; ++ u32 window; ++ u32 blocksize; ++ u16 numblocks; ++ u32 size; ++ ++ struct mtd_info *mtd; ++}; ++#endif ++ ++#ifdef CONFIG_BCMA_NFLASH ++struct mtd_info; ++ ++struct bcma_nflash { ++ bool present; ++ bool boot; /* This is the flash the SoC boots from */ ++ ++ struct mtd_info *mtd; ++}; ++#endif ++ + struct bcma_serial_port { + void *regs; + unsigned long clockspeed; +@@ -445,11 +554,18 @@ struct bcma_drv_cc { + u32 capabilities; + u32 capabilities_ext; + u8 setup_done:1; ++ u8 early_setup_done:1; + /* Fast Powerup Delay constant */ + u16 fast_pwrup_delay; + struct bcma_chipcommon_pmu pmu; + #ifdef CONFIG_BCMA_DRIVER_MIPS + struct bcma_pflash pflash; ++#ifdef CONFIG_BCMA_SFLASH ++ struct bcma_sflash sflash; ++#endif ++#ifdef CONFIG_BCMA_NFLASH ++ struct bcma_nflash nflash; ++#endif + + int nr_serial_ports; + struct bcma_serial_port serial_ports[4]; +@@ -470,6 +586,7 @@ struct bcma_drv_cc { + bcma_cc_write32(cc, offset, (bcma_cc_read32(cc, offset) & (mask)) | (set)) + + extern void bcma_core_chipcommon_init(struct bcma_drv_cc *cc); ++extern void bcma_core_chipcommon_early_init(struct bcma_drv_cc *cc); + + extern void bcma_chipco_suspend(struct bcma_drv_cc *cc); + extern void bcma_chipco_resume(struct bcma_drv_cc *cc); +@@ -493,6 +610,7 @@ u32 bcma_chipco_gpio_polarity(struct bcm + + /* PMU support */ + extern void bcma_pmu_init(struct bcma_drv_cc *cc); ++extern void bcma_pmu_early_init(struct bcma_drv_cc *cc); + + extern void bcma_chipco_pll_write(struct bcma_drv_cc *cc, u32 offset, + u32 value); +--- a/include/linux/bcma/bcma_driver_mips.h ++++ b/include/linux/bcma/bcma_driver_mips.h +@@ -35,13 +35,16 @@ struct bcma_device; + struct bcma_drv_mips { + struct bcma_device *core; + u8 setup_done:1; ++ u8 early_setup_done:1; + unsigned int assigned_irqs; + }; + + #ifdef CONFIG_BCMA_DRIVER_MIPS + extern void bcma_core_mips_init(struct bcma_drv_mips *mcore); ++extern void bcma_core_mips_early_init(struct bcma_drv_mips *mcore); + #else + static inline void bcma_core_mips_init(struct bcma_drv_mips *mcore) { } ++static inline void bcma_core_mips_early_init(struct bcma_drv_mips *mcore) { } + #endif + + extern u32 bcma_cpu_clock(struct bcma_drv_mips *mcore); +--- a/include/linux/bcma/bcma_regs.h ++++ b/include/linux/bcma/bcma_regs.h +@@ -11,11 +11,13 @@ + #define BCMA_CLKCTLST_HAVEHTREQ 0x00000010 /* HT available request */ + #define BCMA_CLKCTLST_HWCROFF 0x00000020 /* Force HW clock request off */ + #define BCMA_CLKCTLST_EXTRESREQ 0x00000700 /* Mask of external resource requests */ ++#define BCMA_CLKCTLST_EXTRESREQ_SHIFT 8 + #define BCMA_CLKCTLST_HAVEALP 0x00010000 /* ALP available */ + #define BCMA_CLKCTLST_HAVEHT 0x00020000 /* HT available */ + #define BCMA_CLKCTLST_BP_ON_ALP 0x00040000 /* RO: running on ALP clock */ + #define BCMA_CLKCTLST_BP_ON_HT 0x00080000 /* RO: running on HT clock */ + #define BCMA_CLKCTLST_EXTRESST 0x07000000 /* Mask of external resource status */ ++#define BCMA_CLKCTLST_EXTRESST_SHIFT 24 + /* Is there any BCM4328 on BCMA bus? */ + #define BCMA_CLKCTLST_4328A0_HAVEHT 0x00010000 /* 4328a0 has reversed bits */ + #define BCMA_CLKCTLST_4328A0_HAVEALP 0x00020000 /* 4328a0 has reversed bits */ +@@ -83,4 +85,9 @@ + * (2 ZettaBytes), high 32 bits + */ + ++#define BCMA_SOC_FLASH1 0x1fc00000 /* MIPS Flash Region 1 */ ++#define BCMA_SOC_FLASH1_SZ 0x00400000 /* MIPS Size of Flash Region 1 */ ++#define BCMA_SOC_FLASH2 0x1c000000 /* Flash Region 2 (region 1 shadowed here) */ ++#define BCMA_SOC_FLASH2_SZ 0x02000000 /* Size of Flash Region 2 */ ++ + #endif /* LINUX_BCMA_REGS_H_ */ |