add all source code from linksys/broadcom which is free, to cvs for better maintainence inside

openwrt. this gives us the ability to better support different hardware models, without changing
any external tar-balls. only et.o and wl.o is missing and is fetched from my webserver.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk/openwrt@379 3c298f89-4303-0410-b956-a3cf2f4a3e73

1 files changed, 91 insertions, 0 deletions

diff --git a/package/linux/kernel-source/include/bcm4710.h b/package/linux/kernel-source/include/bcm4710.h
new file mode 100644
index 000000000..8b059978b
--- /dev/null
+++ b/package/linux/kernel-source/include/bcm4710.h
@@ -0,0 +1,91 @@
+/*
+ * BCM4710 address space map and definitions
+ * Think twice before adding to this file, this is not the kitchen sink
+ * These definitions are not guaranteed for all 47xx chips, only the 4710
+ *
+ * Copyright 2004, Broadcom Corporation   
+ * All Rights Reserved.   
+ *    
+ * THIS SOFTWARE IS OFFERED "AS IS", AND BROADCOM GRANTS NO WARRANTIES OF ANY   
+ * KIND, EXPRESS OR IMPLIED, BY STATUTE, COMMUNICATION OR OTHERWISE. BROADCOM   
+ * SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS   
+ * FOR A SPECIFIC PURPOSE OR NONINFRINGEMENT CONCERNING THIS SOFTWARE.   
+ *
+ * $Id$
+ */
+
+#ifndef _bcm4710_h_
+#define _bcm4710_h_
+
+/* Address map */
+#define BCM4710_SDRAM		0x00000000	/* Physical SDRAM */
+#define BCM4710_PCI_MEM		0x08000000	/* Host Mode PCI memory access space (64 MB) */
+#define BCM4710_PCI_CFG		0x0c000000	/* Host Mode PCI configuration space (64 MB) */
+#define BCM4710_PCI_DMA		0x40000000	/* Client Mode PCI memory access space (1 GB) */
+#define	BCM4710_SDRAM_SWAPPED	0x10000000	/* Byteswapped Physical SDRAM */
+#define BCM4710_ENUM		0x18000000	/* Beginning of core enumeration space */
+
+/* Core register space */
+#define BCM4710_REG_SDRAM	0x18000000	/* SDRAM core registers */
+#define BCM4710_REG_ILINE20	0x18001000	/* InsideLine20 core registers */
+#define BCM4710_REG_EMAC0	0x18002000	/* Ethernet MAC 0 core registers */
+#define BCM4710_REG_CODEC	0x18003000	/* Codec core registers */
+#define BCM4710_REG_USB		0x18004000	/* USB core registers */
+#define BCM4710_REG_PCI		0x18005000	/* PCI core registers */
+#define BCM4710_REG_MIPS	0x18006000	/* MIPS core registers */
+#define BCM4710_REG_EXTIF	0x18007000	/* External Interface core registers */
+#define BCM4710_REG_EMAC1	0x18008000	/* Ethernet MAC 1 core registers */
+
+#define	BCM4710_EXTIF		0x1f000000	/* External Interface base address */
+#define BCM4710_PCMCIA_MEM	0x1f000000	/* External Interface PCMCIA memory access */
+#define BCM4710_PCMCIA_IO	0x1f100000	/* PCMCIA I/O access */
+#define BCM4710_PCMCIA_CONF	0x1f200000	/* PCMCIA configuration */
+#define BCM4710_PROG		0x1f800000	/* Programable interface */
+#define BCM4710_FLASH		0x1fc00000	/* Flash */
+
+#define	BCM4710_EJTAG		0xff200000	/* MIPS EJTAG space (2M) */
+
+#define	BCM4710_UART		(BCM4710_REG_EXTIF + 0x00000300)
+
+#define	BCM4710_EUART		(BCM4710_EXTIF + 0x00800000)
+#define	BCM4710_LED		(BCM4710_EXTIF + 0x00900000)
+
+#define	SBFLAG_PCI	0
+#define	SBFLAG_ENET0	1
+#define	SBFLAG_ILINE20	2
+#define	SBFLAG_CODEC	3
+#define	SBFLAG_USB	4
+#define	SBFLAG_EXTIF	5
+#define	SBFLAG_ENET1	6
+
+#ifdef	CONFIG_HWSIM
+#define	BCM4710_TRACE(trval)        do { *((int *)0xa0000f18) = (trval); } while (0)
+#else
+#define	BCM4710_TRACE(trval)
+#endif
+
+
+/* BCM94702 CPCI -ExtIF used for LocalBus devs */
+
+#define BCM94702_CPCI_RESET_ADDR    	 BCM4710_EXTIF
+#define BCM94702_CPCI_BOARDID_ADDR  	(BCM4710_EXTIF | 0x4000)
+#define BCM94702_CPCI_DOC_ADDR      	(BCM4710_EXTIF | 0x6000)
+#define BCM94702_DOC_ADDR                BCM94702_CPCI_DOC_ADDR
+#define BCM94702_CPCI_LED_ADDR      	(BCM4710_EXTIF | 0xc000)
+#define BCM94702_CPCI_NVRAM_ADDR    	(BCM4710_EXTIF | 0xe000)
+#define BCM94702_CPCI_NVRAM_SIZE         0x1ff0 /* 8K NVRAM : DS1743/STM48txx*/
+#define BCM94702_CPCI_TOD_REG_BASE       (BCM94702_CPCI_NVRAM_ADDR | 0x1ff0)
+
+#define LED_REG(x)      \
+ (*(volatile unsigned char *) (KSEG1ADDR(BCM94702_CPCI_LED_ADDR) + (x)))
+
+/* 
+ * Reset function implemented in PLD.  Read or write should trigger hard reset 
+ */
+#define SYS_HARD_RESET()   \
+    { for (;;) \
+     *( (volatile unsigned char *)\
+      KSEG1ADDR(BCM94702_CPCI_RESET_ADDR) ) = 0x80; \
+    }
+
+#endif /* _bcm4710_h_ */